Installing the hood – FRIGIDAIRE RH36WC60GS User Manual

Page 7

Advertising
background image

7

7

7

7

7

Installing the hood

Installing the hood

ttttt For the most efficient air flow exhaust, use a

straight run or as few elbows as possible.

Vent unit to outside of building and recirculating.

ttttt On avarage 2 to 3 hours are necessary to com-

plete installation (without considering cut to be
done on wall and or on cabinet, installation of
ducts , conduit and electrical connections to the
mains).

ttttt The hood is fitted with Screws and Drywall

Anchors suitable for most surfaces, consult a
Qualified Installer, check if they perfectly fit with
your cabinet/wall.

ttttt Do not use flex ducting.

ttttt COLD WEATHER installations should have an

additional backdraft damper that is already installed
to minimize backward cold air flow and a nonmetallic
thermal break to minimize conduction of outside
temperatures as part of the ductwork. The
damper should be on the cold air side of the
thermal break.
The break should be as close as possible to
where the ducting enters the heated portion of
the house.

ttttt Make up air: Local building codes may require the

use of Make-Up Air Systems when using Ducted
Ventilation Systems greater than specified CFM of
air movement.
The specified CFM varies from locale to locale.
Consult your HVAC professional for specific
requirements in your area.

ttttt TTTTTypical installation

ypical installation

ypical installation

ypical installation

ypical installation

Min installation height from the range top to the
bottom of the hood is 30" if a gas range is used
or 24" to 30" if an electric range is used.
These hoods ar

These hoods ar

These hoods ar

These hoods ar

These hoods ar e not r

e not r

e not r

e not r

e not recommended to be used

ecommended to be used

ecommended to be used

ecommended to be used

ecommended to be used

over indoor grills.

over indoor grills.

over indoor grills.

over indoor grills.

over indoor grills.

The hood may be installed onto a wall and vented to
the outdoors, or it can be installed for recirculating
operation (recirculating accessories not supplied with
the hood).
This hood can be installed over any electric and gas
cooktop/range.
It can not be installed over any pr

It can not be installed over any pr

It can not be installed over any pr

It can not be installed over any pr

It can not be installed over any pr ofessional

ofessional

ofessional

ofessional

ofessional

cooktop / range.

cooktop / range.

cooktop / range.

cooktop / range.

cooktop / range.

Installing pr

Installing pr

Installing pr

Installing pr

Installing preparation

eparation

eparation

eparation

eparation

Advance planning

Advance planning

Advance planning

Advance planning

Advance planning
t Determine the exact location of the vent hood.

t Plan the route for venting exhaust to the

outdoors.

t Use the shortest and straightest duct route

possible.
Refer to “ Ductwork installation guidelines

Ductwork installation guidelines

Ductwork installation guidelines

Ductwork installation guidelines

Ductwork installation guidelines”

paragraph for further informations.

t Install a wall cap with damper or roof cap at the

exterior opening. Order the wall or roof cap and
anytransition needed in advance.

t Use 8" round metal ductwork only.

W

W

W

W

Wall framing for adequate support

all framing for adequate support

all framing for adequate support

all framing for adequate support

all framing for adequate support

t This vent hood is heavy.

‘Adequate structure and support must be
provided in all types of installations. The hood
must be secure to vertical studs in the wall, or to
a horizontal support.

t The vent hood should be on site before final

framing and wall finishing. This will help to
accurately locate the duct work and electrical
service.

t Installation will be easier if the vent hood is

installed before the cook-top and countertop are
installed.

Removing the packaging

Removing the packaging

Removing the packaging

Removing the packaging

Removing the packaging

Remove carton carefully, Wear gloves to protect
against sharp edges.

Remove the protective film covering the product
before putting into operation.

Advertising
This manual is related to the following products: