FRIGIDAIRE 134431300D - Manual (Page 2)

PN 134431300D (0801)
Options
To select an option, press OPTIONS until the
indicator for the desired option flashes, then press
Select. If an option is not available for a cycle, the
indicator will not light. Follow the same steps to
delete an option.
The Cycle Signal will sound at the end of the cycle
and periodically during Press Saver.
Select Shrink Guard to lower the initial drying
temperature to protect fabrics from overdrying.
Select Press Saver if the dried load might not be
removed promptly at the end of the cycle. The dry
load will continue to tumbling without heat for 30
minutes to help reduce wrinkling. When the Cycle
Signal is selected, a beep will be heard periodically.
The load may be removed any time during Press
Saver.
Dryer Features
(Control Lock)
To avoid having someone accidentally start or stop
the washer, press OPTIONS and Select at the same
time and hold for about 10 seconds until the
(Control Lock) lights up. “LOC” will be displayed
alternately with the estimated cycle time. Turning
the Cycle Selector knob or pressing any button
will produce flashing indicator lights and/or beeping.
To unlock the controls, press and hold OPTIONS
and Select for about 10 seconds.
Status Lights
The following indicators may be lighted during the
cycle:
• Drying
• Cool Down
• Press Saver
• Clean Lint Filter
• (Control Lock)
Cycle Selection (Con’t)
Quick
Select this cycle to quickly dry a small load made
up of just a few items. It provides approximately
20 minutes of tumbling followed by a 10-minute cool
down period.
Bulky
Select this cycle to dry a comforter, blanket,
sleeping bag or similar item.Cool Down is
approximately 10 minutes.
Timed Dry
To manually select the drying time for any load,
turn the knob to a numbered setting. Drying times
from 15 to 90 minutes are available in 15-minute
increments. You will not be able to select a cycle
or dryness level. Timed Dry is recommended when
using the No Heat option.
Note: To change cycles, press Pause/Cancel
twice.
To avoid fire hazard, do not use heat
to dry items containing feathers or down, foam
rubber, plastic, or similarly textured, rubber-like
materials. Use the No Heat setting only.
Cycle Settings
Appropriate drying temperature, dryness level and
options will automatically be indicated for each
cycle. The TEMP, DRYNESS and OPTIONS
settings can be changed before the cycle is started.
Those adjustments will automatically be
remembered each time that cycle is selected. If a
temperature, dryness level or option is not
recommended for a cycle, the indicator will not light.
If changes are attempted after the cycle starts, the
status lights will blink, the signal will beep and “Err”
will be displayed. To change a setting after the
cycle starts, press Pause/Cancel once, adjust the
setting and press START to resume the cycle. See
the “Dryer Settings Chart” for more details.
Drying Temperature
For best results, follow the fabric care label
instructions on items to be dried. To change the
drying temperature, press TEMP to scroll to the
desired heat. To protect your wardrobe, not all
temperatures are available with every cycle.
High heat is recommended for sturdy fabrics.
Medium High heat is recommended for most
cotton fabrics.
Medium heat is recommended for wrinkle free,
permanent press and lightweight fabrics.
Low heat is recommended for delicate fabrics.
No Heat should only be used with a Timed Dry
setting to dry items containing feathers, down, foam
rubber, plastics or rubber-like materials; to freshen
clothing, pillows or blankets; or to dust draperies.
Note: Using No Heat in any Auto Dry cycle will
result in long drying times and /or wet
loads at the end of the cycle.
Dryness Level
To change the dryness level, press DRYNESS until
the desired selection is made.
Select Normal for
most loads.
Occasionally a load may seem too damp or over-
dried at the end of the cycle. To increase drying
time for similar loads in the future, select More
Dry. For loads requiring less drying time, select
Less Dry.
Select Damp Dry for items you wish to partially
dry before hanging or ironing.
Note: To prevent over-drying, not every dryness
level is available with every cycle.