GE 26999 - Manual

Plug the power adaptor cord into the power jack on the bottom of
the base and the other end into an electrical outlet. The in use/charge
indicator (on the base) turns on to indicate the battery is charging when
the handset is on the cradle.
Allow the phone to charge for 16 hours prior to first use. If you don’t
properly charge the phone, battery performance is compromised.
CAUTION: Use only the ATLINKS USA, Inc. power adaptor
5-2512 (black) or 5-2618 (gray) power adaptor that came with
this unit. Using other power adaptors may damage the unit.
Connecting the Telephone Line
Plug one end of the telephone line cord into the jack on the bottom of
the base called PHONE LINE and the other end into your home’s modular
phone jack. Place the handset in the cradle on the base.
Wall Mounting
If you want to mount the phone on a wall, slip the mounting holes (on the
back of the base) over the wall plate posts, and slide the unit down into
place. (Wall plate not included.)
Handset Layout
Telephone Jack Requirements
To use this phone, you need an RJ11C type modular
telephone jack, which might look like the one pictured
here, installed in your home. If you don’t have a
modular jack, call your local phone company to find
out how to get one installed.
Digital Security System
Your cordless phone uses a digital security system to protect against
false ringing, unauthorized access, and charges to your phone line.
When you place the handset in the base, the unit verifies its security
code. After a power outage or battery replacement, you should place the
handset in the base for about 20 seconds to reset the code.
INSTALLATION NOTE: Some cordless telephones operate at
frequencies that may cause or receive interference with nearby
TVs, microwave ovens, and VCRs. To minimize or prevent such
interference, the base of the cordless telephone should not be
placed near or on top of a TV, microwave oven, or VCR. If such
interference continues, move the cordless telephone farther away
from these appliances. Certain other communications devices may
also use the 900 MHz frequency for communication, and, if not
properly set, these devices may interfere with each other and/or
your new telephone. If you are concerned with interference, please
refer to the owner’s manual for these devices on how to properly
set channels to avoid interference. Typical devices that may use the
900 MHz frequency for communication include wireless audio/
video senders, wireless computer networks, multi-handset cordless
telephone systems, and some long-range cordless telephone systems.
Important Installation Information
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
• Never touch uninsulated telephone wires or terminals, unless the
telephone line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
• Temporarily disconnect any equipment connected to the phone such as
faxes, other phones, or modems.
Installing the Phone
Your cordless telephone/answering system should be placed on a level
surface such as a desk or table top, or you can mount it on a wall.
Installing the Handset Battery
NOTE: You must connect the handset battery before use.
1. Locate battery and battery door which are packaged together inside a
plastic bag and are separate from the handset.
2. Locate the battery compartment on the back of the handset.
3. Plug the battery pack cord into the jack inside the compartment.
NOTE: It is important to maintain the polarity (black and red
wires) to the jack inside the compartment. To ensure proper battery
installation, the connector is keyed and can be inserted only one way.
Interference Information
This equipment generates and uses radio frequency energy which may
interfere with residential radio and television reception if not properly
installed and used in accordance with instructions contained in this
manual. Reasonable protection against such interference is ensured,
although there is no guarantee this will not occur in a given installation.
If interference is suspected and verified by switching this equipment on
and off, the user is encouraged to try to correct the interference by one or
more of the following measures: Reorient the radio/television receiver’s
antenna, relocate the equipment with respect to the receiver, plug the
equipment and receiver into separate circuit outlets. The user may also
wish to consult a qualified radio/television technician for additional
suggestions. This equipment has been fully tested and complies with
all limits for Class B computing devices pursuant to part 15 FCC Rules
and Regulations. This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions: (1) This device may
not cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
Licensing
Licensed under US Patent 6,427,009.
Hearing Aid Compatibility (HAC)
This telephone system meets FCC standards for Hearing Aid
Compatibility.
REN NUMBER IS LOCATED ON THE CABINET BOTTOM
Introduction
CAUTION: When using telephone equipment, there are basic
safety instructions that should always be followed. Refer to the
IMPORTANT SAFETY INSTRUCTIONS provided with this
product and save them for future reference.
Your cordless telephone/answering system with Caller ID and
Call Waiting is designed to give you flexibility in use and high quality
performance. To get the most from your new cordless telephone/
answering system, we suggest that you take a few minutes right now to
read through this instruction manual. This telephone is a multifunction
product for use with the Call Waiting and Caller ID services available from
your local telephone company. Your Caller ID Call Waiting phone allows
you to:
• View the name and telephone number of a caller (Call Waiting Caller
ID).
• Identify callers before you answer the phone.
• View the time and date of each incoming call.
• Record up to 20 Caller ID messages sequentially.
• Know who called while you are on the other line or when
you were away.
• Screen unwanted calls, eliminate harassment from annoying calls, or
to get prepared before answering a call.
IMPORTANT: In order to use all of the features of this telephone,
you must subscribe to two separate services available from your local
telephone company: the standard Name/Number Caller ID Service
to know who is calling when the phone rings and Caller ID with Call
Waiting Service to know who is calling while you are on the phone.
Because cordless phones operate on electricity, you should have at
least one phone in your home that isn’t cordless, in case the power
in your home goes out.
5. Close the battery compartment by pushing the door up until it snaps
into place.
6. Place the handset in the charging cradle.
Connecting the AC (Electrical) Power
40 Channel 900MHz Call Waiting
Caller ID Cordless Telephone/
Answering System
User’s Guide
26999
Programmable Menus
There are six programmable menus available: Language, Local Area Code,
Ringer Tone, Tone/Pulse, Ringer On/ Off, and Factory Default. When you
program these settings, make sure the phone is OFF (not in talk mode).
Pressing the *tone/exit button will remove you from the menu selection
process without changing the feature you are in.
Display Language
1. Press the flash/program button until 1ENG 2FRA 3ESP shows in the
display.
2. Use the CID/VOL (or) button or the handset number pad to select 1
(English), 2 (French), or 3 (Spanish). The default setting is “1ENG”.
3. Press the flash/program button to confirm and to advance to the next
menu feature.
Local Area Code
If you enter your local 3-digit area code in the area code menu, your local
area code does not display on the Caller ID (CID) list. Instead, you only
see the local 7-digit number. Calls received from outside your local area
code will display the full 10-digit number.
1. Press the flash/program button until AREA CODE- - - shows in the
display. The default setting is “- - -”.
2. Use the handset number pad to enter your 3-digit area code.
NOTE: If you make a mistake, press the chan/delete button to
erase the incorrect area code and repeat step 2.
3. Press the flash/program button to confirm and to advance to the next menu
feature.
Ringer Tone
1. Press the flash/program button until RINGER TONE shows in the
display.
2. Use the CID/VOL (or) button or the handset number pad (1-3) to
enter your selection from Ringer Tone 1, 2, or 3. The default setting is
“RINGER TONE 1”.
3. Press the flash/program button to confirm and to advance to the next menu
feature.
Tone/Pulse
1. Press the flash/program button until 1 TONE 2 PULSE shows in the
display.
2. Use the CID/VOL (
 or ) button or the handset number pad to enter
your selection. The default setting is “1 TONE”.
3. Press the flash/program button to confirm and to advance to the next
menu feature.
Ringer ON/OFF
1. Press the flash/program button until RINGER 1ON 2OFF shows in the
display.
2. Use the CID/VOL (
 or ) button or the handset number pad to enter
your selection. The default setting is “1ON”.
3. Press the flash/program button to confirm and to advance to the next
menu feature.
NOTE: If you turn the ringer OFF, RINGER OFF shows in the
handset display.
Factory Default
This feature allows you to restore the unit’s original features.
1. Press the flash/program button until DEFAULT shows in the display.
2. Use the CID/VOL (
 or ) button to scroll to YES. The default setting is
“NO”.
3. Press flash/program to confirm. You will hear a confirmation tone.
Cordless Phone Basics
Making a Call
1. Press the TALK/CALL BACK button and dial the desired number.
-OR-
To perform preview dial, dial the number first then press the TALK/
CALL BACK button.
2. To hang up, press the TALK/CALL BACK button or place the handset in
the base cradle.
IMPORTANT: Because cordless phones operate on electricity, you
should have at least one phone in your home that isn’t cordless, in
case the power in your home goes out.
Redial
Press the redial button to quickly dial the last number you called (up to 32
digits).
If you get a busy signal, and want to keep dialing the number, press
redial to dial the number again.
Receiving a Call
1. To answer a call press the TALK/CALL BACK button on the handset
before you begin speaking.
2. To hang up, press the TALK/CALL BACK button or place the handset in
the base cradle.
In Use Indicator
When the in use/charge indicator on the base is lit, the handset is either
in use or charging. The in use/charge indicator on the base flashes when
you receive a call.
Flash
If you subscribe to the combined Call Waiting Caller ID service from
your local telephone company you will receive Caller ID information (if
available) on Call Waiting calls. During a phone call, you will hear a beep
to indicate another call is waiting on the line and Caller ID information
for the waiting call shows on the handset display. To connect the waiting
call, press the flash/program button on the handset and your original call
is put on hold. You may switch back and forth between the two calls by
pressing the flash/program button.
TIP: Do not use the TALK/CALL BACK button to activate custom
calling services such as call waiting, or you’ll hang up the phone.
Volume
When the phone is ON, press the CID/VOL (or) on the handset to
adjust the volume of the handset’s earpiece. There are four settings. Press
the right arrow to increase the volume and left arrow to decrease the
volume. You will see the volume setting on the handset display. VOL 4 is
the maximum and VOL 1 is the minimum.
Channel Button
While talking on the phone, you might need to manually change the
channel in order to reduce static caused by appliances, such as baby
monitors, garage door openers, microwave ovens, or other cordless
phones. Press and release the chan/delete button to move to the next
clear channel.
Temporary Tone
This feature is useful only if you have pulse (rotary) service. Temporary
Tone Dialing enables pulse (rotary) service phone users to access
touchtone services offered by banks, credit card companies, etc. For
example, when you call your bank you may need to enter your bank
account number. Temporarily switching to touchtone mode allows you to
send your number.
1. Dial the telephone number and wait for the line to connect.
2. When your call is answered, press the *tone/exit button on the handset
to temporarily change from pulse dialing to tone dialing.
3. Follow the automated instructions to get the information you need.
4. Hang up the handset and the phone automatically returns to pulse
(rotary) dialing mode.
Exit
Press the *tone/exit button to cancel any command you initiated.
Paging the Handset
This feature helps to locate a misplaced handset.
Press the page button on the base. The handset will beep for about two
minutes or until you press TALK/CALL BACK on the handset or press the
page button on the base.
NOTE: You can still page the handset if the ringer is turned off. If
the battery is dead, the Paging feature will not work.
Caller ID Features
Caller ID (CID) is a service available from your local telephone company.
For Caller ID to work on this system, you must subscribe to Caller ID
service. To receive Caller ID information for a Call Waiting call, you must
subscribe to the combined Caller ID Call Waiting service. The unit can
store up to 20 calls for later review.
When your telephone rings, and you are subscribed to Caller ID Call
Waiting service, you will receive information (if available) transmitted by
your local telephone company. You will also receive Caller ID information
from Call Waiting calls. If you receive an incoming call and you are
already on the phone, a beep indicates the presence of a Call Waiting Call
on the line, and Caller ID information for the Call Waiting call shows on
the display. This information may include the phone number, date and
time; or the name, phone number, and date and time.
Receiving and Storing Calls
When you receive a call, the information is transmitted by the phone
company to your Caller ID telephone between the first and second ring.
VERY IMPORTANT: The Caller ID feature of this product requires
a subscription to Caller ID service from your telephone company.
When the phone’s memory is full, a new call automatically replaces the
oldest call in memory. NEW appears in the display for calls received that
have not been reviewed.
NOTE: Check with your local phone company regarding name
service availability.
Reviewing Caller ID Records
As calls are received and stored, the display is updated to let you know
how many calls have been received.
• Make sure the phone is OFF (not in TALK mode).
• Press the CID/VOL () button to scroll through the call records from the
most recent to the oldest.
• Press the CID/VOL () button to scroll through the call records from the
oldest to the newest.
Deleting the Current Record
1. When the Caller ID record shows in the display, press and release the
chan/delete button. The display shows DELETE CALL ID?
2. Press chan/delete button again to confirm. You will hear a confirmation
tone, the display shows DELETED, then the next Caller ID record
appears in the display.
Deleting All Records
1. Press the CID/VOL (or) button until a Caller ID record is displayed.
2. Press and hold chan/delete until unit beeps. The display shows DELETE
ALL?
3. Press chan/delete again to erase all records. You will hear a
confirmation tone, and the display shows NO CALLS.
Storing Caller ID Records in Memory
NOTE: Caller ID record should be in correct format for dialing as
record cannot be changed once it is stored in memory location.
1. Press the CID/VOL (or) button until the desired Caller ID record is
displayed.
2. Press the memory button.
3. Press a number (0-9) to store the dialed number in that memory
location. You will hear a confirmation tone. Example, press the
number 1 key to store the record in memory location 1.
To Replace an Old Memory with a New Caller ID
Record:
1. Repeat steps 1 through 3 in Transferring Caller ID Records to Memory.
After entering the memory location, REPLACE MEMO? shows in the
display.
2. Press the memory button again, and the new Caller ID record replaces
the old memory in that location. You will hear a confirmation tone.
Dialing a Caller ID Number
1. Make sure the phone is OFF (not in TALK mode).
2. Use the CID/VOL (or) button to display the desired Caller ID record.
3. Press the TALK/CALL BACK button to dial the number.
Changing the Number Format
The format/answerer button lets you change the format of the displayed
number. The available formats are as follows.
7-digit 7-digit telephone number.
10-digit 3-digit area code + 7-digit telephone number.
11-digit long distance code “1” + 3-digit area code + 7-digit telephone
number.
1. Use the CID/VOL (or) button to scroll to the number you want to
call back.
2. If the number does not dial as shown, press the format/answerer
button. Repeat if necessary, until the correct number of digits shows in
the display.
3. Press the TALK/CALL BACK button.
Important Information
NOTICE: This product meets the applicable Industry Canada
technical specifications.
The equipment must be installed using an acceptable method of
connection. The customer should be aware that compliance with the
above conditions may not prevent degradation of service in some
situations.
Repairs to certified equipment should be made by an authorized
Canadian maintenance facility designated by the supplier. Any repairs
or alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to
request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic
water pipe systems, if present, are connected together. This precaution
may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections
themselves, but should contact the appropriate electric inspection
authority, or electrician, as appropriate.
NOTES: This equipment may not be used on coin service provided by the
telephone company.
Model 26999GF
00006816 (Rev. 0 CAN E)
05-32
Printed in China 4. Insert the battery pack.
Memory
Store up to ten 24-digit numbers in memory for quick dialing. This
memory feature is in addition to the 20 Caller ID records that can be
stored in memory.
Storing a Name and Number in Memory
1. Make sure the phone is OFF (not in TALK mode).
2. Press the memory button.
3. Press a number (0-9) to store the dialed number in that memory
location. Or use the CID/VOL (or) to scroll to desired location. If the
memory location is occupied, the memory location and stored name
and number appear on the screen.
NOTE: If the memory location is empty, “EMPTY” appears in the
display.
4. Press the memory button again. The display shows ENTER NAME.
NOTE: If you don’t want to enter the name, skip step 5.
5. Use the handset number keypad to enter a name (up to 15 characters).
More than one letter is stored in each of the number keys. For
example, to enter Bill Smith, press the 2 key twice for the letter B.
Press the 4 key 3 times for the letter I. Press the 5 key 3 times for the
letter L, and wait for 1 second. Press the 5 key 3 times for the second
letter L, and press the 1 key to insert a space between the first and last
name. Press the 7 key 4 times for the letter S; press the 6 key once for
the letter M; press the 4 key 3 times for the letter I; press the 8 key for
the letter T; press the 4 key twice for the letter H.
NOTE: If you make a mistake press the chan/delete button to
backspace and erase the wrong character(s) or number(s).
6. Press the memory button again to save the name. The display shows
ENTER TEL NUMBR.
7. Use the handset number keypad to enter the telephone number (up
to 24 digits, including pauses) and press the memory button again to
save the number. The unit beeps to confirm.
8. To enter another name and number in a different memory location,
return to step 1 and repeat the process.
Storing a Redial Number
1. Repeat steps 1 through 6 in Storing a Name and Number in Memory.
2. Press the redial button.
3. Press the memory button to store the number. You will hear a
confirmation tone.
To Replace an Old Memory with a New Redial Number
1. Repeat steps 1 through 6 in Storing a Name and Number in Memory.
2. Press the redial button.
3. Press the memory button, and REPLACE MEMO? shows in the display.
4. Press the memory button to replace the old memory with the new
redial number. You will hear a confirmation tone.
Changing a Stored Number
1. Repeat steps 1 through 7 in Storing a Name and Number in Memory.
REPLACE MEMO? shows in the display.
2. Press the memory button to store the number. You will hear a
confirmation tone.
Dialing a Stored Number
1. Make sure the phone is ON by pressing the TALK/CALL BACK button.
2. Press the memory button.
3. Press the number (0-9) for the desired memory location. The number
dials automatically.
OR
1. Make sure the phone is OFF (not in TALK mode).
2. Press the memory button.
3. Press the memory location for the phone number you want to dial, or
use the CID/VOL (or) button to scroll through the numbers stored
in memory until the desired number is shown.
4. Press TALK/CALL BACK. The number dials automatically.
Chain Dialing from Memory
Use this feature to make calls which require a sequence of numbers,
such as using a calling card for a frequently called long distance number.
You simply dial each part of the number sequence from memory. The
following example shows how you can use chain dialing to make a call
through a long distance service:
RED WIRE
BLACK WIRE
BATTERY
PRESS DOWN
FIRMLY
Modular
telephone
line jack
Wall plate
Before You Begin
Parts Checklist
Make sure your package includes the items shown here.
Telephone Setup
ATLINKS Communications Canada Inc.
© 2005 ATLINKS Communications Canada Inc.
Trademark(s) ® Registered
Marque(s) ® déposée(s)
Base Handset
Line cord
AC
power
adaptor
Handset battery
+
format/answerer
(button)
CID/VOLor
(button)
redial
(button)
TALK/CALL
BACK (button)
flash/program
(button)
*tone/exit
(button)
chan/delete
(channel/
delete button)
memory (button)
#pause (button)
display
review  
(button)
skip  
(button)
play/stop
(button)
erase (button)
+
erase (button)
volume or
(button)
page (button)
memo (button)
PLAY/STOP (button)
display
review/skip or(button)
microphone
answer on/off button
announce button
hour (button)
day/check (button)
min (button)
in use/charge
(indicator)
Time
Date
Number of
Calls
Caller ID
name
Caller ID
phone number