GE BedroomPhone 00023810 - Manual

2. Plug the other end into a wall jack.
3. Plug one end of the coiled handset cord into the jack on the
handset.
4. Plug the other end into the HANDSET jack on the back of the base.
5. Place the handset on the base cradle.
6. Set the RINGER and DISPLAY BRIGHTNESS switches on the back of
the base to the desired settings.
7. Set the VOL switch on the side of the handset to the
desired setting..
Connecting the Electrical Power
1. Plug one end of the power supply cord into the back of the base.
2. Plug the other end into an electrical outlet.
CAUTION: To reduce risk of personal injury, fire, or
damage use only the 5-2836 power adaptor listed in
the user’s guide. This power adaptor is intended to
be correctly orientated in a vertical or floor mount
position.
“No Worry” Battery Backup
This telephone is equipped with a memory holding system
powered by a customer-installed 9-volt alkaline battery
(not included).
When electrical power is interrupted, or
the electrical line is unplugged, the battery
operates the clock to retain the time of day
and alarm settings in memory. When the
unit is running on battery power, the digital
display does not light up; however, if wake time occurs during the
power interruption, the alarm buzzer sounds (regardless of the type of
alarm tone selected) if remaining battery power is adequate. Normal
operation resumes after electrical power is restored.
NOTE: The battery power indicator illuminates if the
battery power level is low or if no battery is installed.
Please replace/install the batteries as soon as
possible in order to maintain Caller ID operation.
Install the backup battery as follows:
1. Remove the battery compartment cover located on the bottom of
the base.
2. Connect a fresh 9-volt alkaline battery (not included). Interlock the
large and small contacts on the battery clip and the battery. Once
connected, place the battery inside the battery compartment.
3. Replace the battery compartment cover.
NOTE: 9V Alkaline (NEDA 1604A) batteries are
recommended.
NOTE: If battery is not installed:
a) All memory will be lost if the unit is unplugged for
more than 60 seconds.
b) The clock will stop running during a power outage
period but will start running when power resumes.
The clock will blink to indicate that the time may not
be correct.
IMPORTANT: If storing this unit for more than 30
days, remove the battery.
Installing the Phone
Connecting the Telephone Line
Choose the best location to install your telephone. Your telephone
should be placed on a level surface, such as a desk or table top.
1. Plug one end of the straight telephone line cord into the PHONE
LINE jack on the base.
Model 29298
00023810 (REV. 0 DOM E)
08-17
Printed in China
Equipment Approval Information
Your telephone equipment is approved for connection to the Public Switched
Telephone Network and is in compliance with parts 15 and 68, FCC Rules
and Regulations and the Technical Requirements for Telephone Terminal
Equipment published by ACTA.
1 Notification to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other
information, the US number and Ringer Equivalence Number (REN) for
the equipment. You must, upon request, provide this information to your
telephone company.
The REN is useful in determining the number of devices you may connect
to your telephone line and still have all of these devices ring when your
telephone number is called. In most (but not all) areas, the sum of the RENs
of all devices connected to one line should not exceed 5. To be certain of the
number of devices you may connect to your line as determined by the REN,
you should contact your local telephone company.
A plug and jack used to connect this equipment to the premises wiring
and telephone network must comply with the applicable FCC Part 68 rules
and requirements adopted by the ACTA. A compliant telephone cord and
modular plug is provided with this product. It is designed to be connected
to a compatible modular jack that is also compliant. See installation
instructions for details.
Notes
• This equipment may not be used on coin service provided by the
telephone company.
• Party lines are subject to state tariffs, and therefore, you may not be able
to use your own telephone equipment if you are on a party line. Check
with your local telephone company.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO
PREVENT FIRE OR
ELECTRICAL SHOCK
HAZARD, DO NOT
EXPOSE THIS
PRODUCT TO RAIN
OR MOISTURE.
THE LIGHTNING
FLASH AND ARROW
HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
“DANGEROUS
VOLTAGE” INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR
BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
CAUTION:
• Notice must be given to the telephone company upon permanent
disconnection of your telephone from your line.
• If your home has specially wired alarm equipment connected to the
telephone line, ensure the installation of this product does not disable your
alarm equipment. If you have questions about what will disable alarm
equipment, consult your telephone company or a qualified installer.
US NUMBER IS IS LOCATED ON THE CABINET BOTTOM
REN NUMBE IS LOCATED ON THE CABINET BOTTOM
2 Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm the
telephone network, the telephone company shall, where practicable, notify
you that temporary discontinuance of service may be required. Where prior
notice is not practicable and the circumstances warrant such action, the
telephone company may temporarily discontinue service immediately. In
case of such temporary discontinuance, the telephone company must: (1)
promptly notify you of such temporary discontinuance; (2) afford you the
opportunity to correct the situation; and (3) inform you of your right to bring
a complaint to the Commission pursuant to procedures set forth in Subpart
E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities,
equipment, operations or procedures where such action is required in
the operation of its business and not inconsistent with FCC Rules and
Regulations. If these changes are expected to affect the use or performance
of your telephone equipment, the telephone company must give you
adequate notice, in writing, to allow you to maintain uninterrupted service.
Interference Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference;
and (2) This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
Privacy of Communications may not be ensured when using this product.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or
television that is “receiving” the interference).
• Reorient or relocate and increase the separation between the
telecommunications equipment and receiving antenna.
• Connect the telecommunications equipment into an outlet on a circuit
different from that to which the receiving antenna is connected.
If these measures do not eliminate the interference, please consult your dealer
or an experienced radio/television technician for additional suggestions. Also,
the Federal Communications Commission has prepared a helpful booklet,
“How To Identify and Resolve Radio/TV Interference Problems.” This booklet is
available from the U.S. Government Printing Office, Washington, D.C. 20402.
Please specify stock number 004-000-00345-4 when ordering copies.
Hearing Aid Compatibility (HAC)
This telephone system meets FCC standards for Hearing Aid Compatibility.
Licensing
Licensed under US Patent 6,427,009.
FCC RF Radiation Exposure
Statement
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 20 centimeters between the radiator and your
body. This transmitter must not be co-located or operated in conjunction with
any other antenna or transmitter.”
Introduction
CAUTION: When using telephone equipment,
there are basic safety instructions that should
always be followed. Refer to the IMPORTANT
SAFETY INSTRUCTIONS provided with this product
and save them for future reference.
Before You Begin
Parts Checklist
Make sure your package includes the following items:
Base Operation
Setting the Clock
1. Slide the set time /alarm switch to clock. The screen flashes the
setting time.
2. Press the <rev/fwrd> or fwrd >> button to set the clock time.
3. Slide the set time/alarm switch to lock. The screen displays the
current time.
Display Backlight
Use the brightness switch to select the desired setting: high or low.
Alarm Operation
The 29298 is equipped with two alarms. The alarms can be set
independently to either radio or buzzer.
Setting the Alarm Time
1. Slide the set time /alarm switch to alarm 1 or alarm 2. The
corresponding alarm time will be shown on the clock display.
2. Press the <rev/fwrd> or fwrd >> button to set the alarm time.
Set Alarm Tone
1. Slide the alarm 1 or alarm 2 switch to choose radio, buzzer or off.
2. The corresponding alarm ON indicator on the display illuminates.
Turning Off the Alarms
1. To turn off the alarm, press the off side of the radio on/off button
once. Alarm is still active and will be delivered when alarm time is
reached again. Alarm ON indicator will remain illuminated.
2. Alarm is turned off by sliding the alarm 1 or alarm 2 switch to “off”
setting.
Snooze Timer
After the wake mode is activated, you can silence for 6 minutes by
pressing the SNOOZE button.
You may use the snooze feature repeatedly.
Using the Sleep Timer
Use the sleep timer to play the radio up to 59 minutes and then have it
shut off automatically.
1. Press the
sleep button once to activate the radio sleep timer.
2. The timer can be adjusted from 59 minutes to 1 minute.
3. To set sleep time, press and hold the
sleep button. The time shown on
the clock display will decrease. Then release the sleep button when the
desired length of time is shown on the clock display.
4. Press the off button to de-activate the sleep function.
Radio Operation
1. Press the on side of the radio on/off button to turn the radio on.
2. Slide the AM/FM switch to select the desired broadcast band.
3. Rotate the radio channel tuning knob to select a radio station /
frequency.
4. Rotate the volume -/+ control knob to adjust the listening level.
5. To turn the radio off, press the off side of the radio on/off button.
NOTE: You can also turn on the radio after lifting
up the handset by pressing the on side of the radio
on/off button.
NOTE: The Radio broadcast will automatically turn
off when you picked up the handset. Broadcast will
resume when you replace the handset on cradle.
AM Antenna
A built-in antenna eliminates the need for an outside antenna for AM
reception. Moving the unit slightly may improve reception of distant
AM signals.
FM Antenna
The power cord acts as your FM antenna. The power cord picks up
moderate to strong signals and eliminates the need for an external
antenna in most strong signal areas. Be sure the power cord is
stretched to its longest length. Do not coil or bunch the cord together.
Changing position of the power cord may improve reception.
Model 29298
Caller ID
BedroomPhone™
with Dual-Wake Alarms
and AM/FM Radio
User’s Guide
Modular
telephone
line jack
Wall plate
Visit the GE website at: www.GE.com/phones
Thomson Inc.
101 West. 103rd St.
Indianapolis, IN 46290-1102
© 2008 Thomson Inc.
Trademark(s) ® Registered
Marca(s) Registrada(s)
Telephone Jack Requirements
To use this phone, you need an RJ11C type
modular telephone jack, which might look like
the one pictured here, installed in your home. If
you don’t have a modular jack, call your local
phone company to find out how to get one
installed.
Important Installation Guidelines
• Install telephone near both a telephone (modular) jack and an
electrical power outlet.
• Avoid sources of noise, such as a window by a busy street,
and electrical noise, such motors, microwave ovens, and
fluorescent lighting.
• Avoid heat sources, such as heating air ducts, heating
appliances, radiators, and direct sunlight.
• Avoid areas of excessive moisture or extremely low temperature.
• Avoid dusty locations.
• Avoid other cordless telephones or personal computers.
Handset Layout
Handset
Base
AC power
adaptor
Telephone line
cord
Handset
cord store mem redial
flash
tone oper
pqrs wxyz tuv
ghi mno jkl
def abc
Base Layout
Telephone Operation
Adjusting the Ringer Volume
You may control the ringer volume level with the switch located on the
side of the base.
= loud
= low
= off
Handset Receiver Volume
Use the VOLUME switch on the rear of the handset to adjust the
handset receiver volume.
= high
= mid
= low
Flash
Press the flash button to activate customer calling services,
such as call transfer, which are services provided by your local
phone company.
Redial
To redial the last number called (up to 32 digits), use the redial feature.
1. Pick up the handset.
2. Press the
redial button.
3. The last number called is automatically redialed.
Using One Touch Redial
If the last call you dialed was busy, you can redial it immediately by
just pressing the redial button and without hanging up the handset.
Setting Up the Caller ID Menu
IMPORTANT: Do not plug the telephone into the wall
jack while setting up the Caller ID menu because an
incoming call may invalidate the information not yet
saved.
1. Place the handset in the cradle on the base.
2. Press the
menu button. the screen displays SET ^ OR .
3. Press the CID5 or 6 button to scroll among the 7 menu screens,
which are:
• SET ^ OR
• Local Area Code (default ” - - -”)
• Regional AC’s-1 (default “- - - - - - - - -”)
• CID LANGUAGE (default English)
• SELECT CONTRAST (default 3)
• T/P DIAL MODE (default tone)
• EXIT SETUP
NOTE: You may press the dial button anytime to exit
the Caller ID Set Up menu. If no buttons are pressed
within 10 seconds, the phone automatically exits the
Caller ID Set Up menu and returns to the NO CALLS
summary screen.
Local Area Code
The telephone uses the programmed area code to determine the
number format to display when a valid Caller ID signal is received. It is
also used for the Dialback feature.
1. Press the
menu button. the screen displays SET ^ OR .
2. Press the CID5 or 6button until the screen displays LOCAL AREA
CODE, The default setting is ”_ _ _” .
3. To enter or change the area code, press the menu button. The
screen displays the area code stored in memory. The left-most digit,
or a minus sign (-) flashes, indicating the unit is ready to accept the
area code entry.
4. Press the CID 6 button to select a number from 0-9 in ascending
order. Or press the CID 5 button to select numbers from 9-0 in
descending order.
5. Press the menu button to advance to the next digit.
6. After the 3rd and last digit is entered, press the menu button to
store the area code and go to the next setting.
NOTE: If you make a mistake, you can simply repeat
the previous steps until your area code is set.
Regional Area Codes for 10-Digit Dialling
Like the Local Area Code, the telephone uses the programmed area
codes to determine the number format to display when a valid Caller
ID signal is received. Calls that match any of the programmed regional
area codes are displayed as 10 digits. This is helpful in areas that have
multiple or overlapping area codes and require 10-digit dialling.
1. Press the menu button. the screen displays
SET ^ OR .
2. Press the CID5 or 6 button until the screen displays REGIONAL
AC’S-1: The default setting is “_ _ _ _ _ _ _ _ _” .
3. To enter or change the area code, press the menu button. The
screen displays the area code stored in memory. The left-most digit,
or minus sign (-), flashes, indicating the unit is ready to accept the
area code entry.
4. Press the CID 5 button to select a number from 9-0 for the first
digit of the area code.
5. When the desired digit is flashing, press the menu button to
advance to the next digit.
6. Press the menu button again to enter the next three-digit regional
area code and repeat steps 4 and 5 until all the REGIONAL AC’S-1
(RAC#1) and REGIONAL AC’S-2 (RAC#1) are entered. A total of 6
sets of Regional Area Codes may be entered.
7. Press the menu button to store the setting and return to the
REGIONAL AREA CODE setting.
8. Press the dial button to exit.
CID Language
This setting allows you to display Caller ID display prompt messages in
English, French or Spanish.
1. Press the
menu button. the screen displays SET ^ OR .
2. Press the CID5 or 6 button until the screen displays CID
LANGUAGE.
3. Press the menu button to show the current language setting. The
default is “English”.
4. Press the CID5 or 6 button to change the language.
5. Press the menu button to store the language and return to the CID
LANGUAGE setting.
Select Contrast
This adjustment allows you to adjust the contrast of the display.
1. Press the
menu button until the screen displays SET ^ OR .
2. Press the CID5 or 6 button until the screen displays SELECT
CONTRAST.
3. Press the menu button to show the current contrast setting. There
are 5 levels of contrast, with the default set to 3.
4. To decrease the contrast, press the CID 5 button to increase the
contrast, press the CID 6 button.
5. Press the menu button to store the contrast setting and return to
the SELECT CONTRAST setting.
Tone/Pulse Dial Mode
This adjustment allows you to select tone (touch-tone) or pulse (rotary)
dialling.
1. Press the
menu button until the screen displays SET ^ OR .
2. Press the CID5 or 6 button until the screen displays T/P DIAL
MODE.
3. Press the menu button to show the current dial mode. The default
is “TONE”.
4. To change the dialling mode, press the CID 5 or 6 button. The
display will alternate between the two dialling modes.
5. Press the menu button to store the dialling mode and return to the
T/P DIAL MODE setting.
Exit Setup
To immediately exit the setup mode, select the EXIT SETUP and press
the dial button.
REMINDER: The time and date is programmed
automatically when the first Caller ID record is
successfully received after the unit is setup.
store mem redial
flash
tone oper
pqrs wxyz tuv
ghi mno jkl
def abc
CID 5or6
(Caller ID
button)
dial
(button)
delete
(button)
menu
(button)
display
*/tone
(button)
redial
(button)
mem
(memory
button)
store
(button)
flash
(button)
VOLUME
(switch)
< rev/fwrd>
(reverse/forward
button)
sleep
(button)
alarm 2
off/buzzer/radio
(switch)
AM/FM
(switch)
set time/alarm
(switch)
radio on/off
(button)
volume
-/+
control
knob
radio
channel
tuning
knob
SNOOZE
(button)
alarm 1
off/buzzer/radio
(switch)
brightness
(switch)
fwrd>>
(fast forward
button)
display
ringer
(switch)
-
-
+
+
Battery clip
Battery
Type
NEDA
1604A
9V
battery
power
indicator