Philips Magnavox CMWV405 - Manual

-  - EN
Select this connection when you want to view
or record a scrambled channel. With this con-
nection, channels cannot be changed on the
unit. You can view or record ONLY the chan-
nels you have selected on the cable box or
the satellite box.
• While you are recording, only the recorded
channel can be viewed.
To select channels of the cable box or
satellite box
) Turn on the unit by pressing
[STANDBY-ON], then press [VCR/TV].
The “POWER” and the “VCR/TV” indicator
on the front panel will appear, then press
[CHANNEL ] to select channel 3 or 4
(the same channel as the output channel of
the cable box or satellite box).
• If you use the channel 4, you need to
change the unit’s RF output to channel 4.
Refer to “RF Output Channel”.
2) At the TV, select channel 3 or 4 (the same
channel as you have selected at step ).
3) On the cable box or satellite box, select the
channel you want to view or record.
You can use the AUDIO OUT jack and
VIDEO OUT jack on the back of the
VCR if your TV has Audio/Video Input
jacks. In this case, you need to set the
TV to external Line Input Mode. Please
refer to your TV’s owner’s manual.
Owner’s Manual
Video Cassette Recorder
CMWV405
VMN22462 / HJ34RCD ★★★★★
Printed in China
ANT IN jack
Connect your antenna or cable box here.
ANT OUT jack
Connect the supplied RF cable to the
antenna input jack on your TV.
Front & Rear Terminals
Stereo TV Connection
• Remote control
(NA374UD) with
two AA batteries
• RF cable
(WPZ090TM002)
• Owner’s manual
(VMN22462)
Supplied Accessory Installing the Batteries for
the Remote Control
Install two AA batteries
(supplied) matching
the polarity indicated
on the bottom of the
remote control.
If channel 3 is already occupied for broadcasting,
) Set your TV to channel 4.
2) Insert a pre-recorded tape into this unit.
3) Press [PLAY B] once.
4) After a few seconds, hold [PLAY B] on the unit for 3 seconds.
• The RF output channel will change to channel 4 from channel 3
and you will see a playback picture.
• When a picture does not appear on the TV screen, repeat step 4.
5) Press [STOP C] to stop playback.
Hint
• The RF output channel
does not change when
you adjust tracking during
playback. In this case, stop
the playback, and start
the playback again. After
that, hold [PLAY B] on the
VCR for 3 seconds again.
VIDEO OUT jack
Connect the video cable here through the video
input jack of a camcorder, another VCR or a TV.
RF Output Channel
AUDIO VIDEO
REW STANDBY-ON F.FWD STOP/EJECT
IR
POWER VCR/TV CST.IN TIMER RECORD
RECORD MENU CHANNEL PLAY
1. Before Using Your VCR
ANT
IN
OUT
RF Cable (supplied)
(Back of VCR)
(Back of TV)
(Back of TV)
Plug the AC power cords of the VCR and TV into the AC outlets.
4
Disconnect
Antenna
or
2
Connect
3
Connect
Antenna
or
Cable TV
Signal
Cable TV
Signal
RF Cable
(not supplied)
RF Cable
(not supplied)
Basic TV Connection
Hint for Cable Box or Satellite Box
ANT IN
OUT
ANT IN
OUT
RF cable
(supplied)
RF Cable (supplied)
RF Cables
(not supplied)
RF Cable
(Back of VCR)
IN OUT E
(Back of TV)
(Back of TV)
IN OUT
(Cable box or
Satellite box)
E
Cable
Signal
Connection B
Antenna or
Cable TV
signal
(Back of VCR)
(Cable box or
Satellite box)
If you need additional operating assist-
ance after reading this owner’s manual
or to order replacement accessories,
please call
TOLL FREE : 1-800-605-8610
http://www.funai-corp.com
AUDIO OUT jack
Connect the audio cable here through to the audio
input jack of a camcorder, another VCR, a stereo
amplifier or an audio system.
ANT
AUDIO
VIDEO
IN
OUT OUT IN
ANT
AUDIO
VIDEO
IN
OUT
OUT IN
ANT IN
OUT
AUDIO
ANT IN
OUT
VIDEO
Audio/Video Cables
(not supplied)
AUDIO IN VIDEO IN
AUDIO IN VIDEO IN
(Back of TV)
IN OUT
(Back of VCR)
AUDIO IN jack
Connect the audio cable coming from the
audio output jack of a camcorder, another
VCR or an audio source here.
• To use the input jacks on the back of this unit, press [0], [0], [1] on the remote control.
• To use the input jacks on the front of this unit, press [0], [0], [2] on the remote control.
VIDEO IN jack
Connect the video cable coming from the
video output jack of a camcorder, another
VCR or an audio-visual source (laser disc
player, video disc player, etc.) here.
CMWV405_HJ34RCD_EN.indd  2006/0/23 6:20:25