Motorola Bluetooth Handsfree Headset HS820 - Manual

1 - CHARGE
2 - PAIR
3 - START
BLUETOOTH
4 - TEST AND
USE
Get Connected in
4 Quick Steps
Quick Start Guide
HS820
Bluetooth®
Handsfree Headset
TEST AND USE
Your phone and headset are now paired
and ready to make and receive calls.
To make a call:
Place the headset over your ear.
On your phone, dial the number you want
to call and press the SEND key.
If your phone and headset are successfully
paired, you will hear ringing on the headset.
After you have successfully paired your
phone and headset, you do not need to
repeat these steps. For daily use, ensure
that your headset is turned ON and that
your phone's Bluetooth feature is ON.
To conserve battery power, turn OFF the
headset when you will not be using it for an
extended time.
4
1
2
QUICK TIPS TROUBLESHOOTING
My phone does not find my headset
Make sure the blue light on your headset is on
and steady when your phone is searching for
devices (see step 2).
My headset worked before but now it's not
working.
Make sure your phone is on and the Bluetooth
feature is turned on in your phone (step 3). If
the Bluetooth feature has been turned off, you
may need to restart the Bluetooth feature (see
step 3) and pair your phone and headset again
(see step 2).
MOTOROLA and the Stylized M Logo are registered in the US
Patent & Trademark Office. The Bluetooth trademarks are
owned by their proprietor and used by Motorola, Inc. under
license. All other product or service names are the property of
their respective owners. © Motorola, Inc. 2005.
Motorola, Inc.
Consumer Advocacy Office
1307 East Algonquin Road
Schaumburg, IL 60196 USA
Guide Number: 6809494A71 -A 3
Charge your headset for 2 hours:
Plug the Motorola charger into the top of
the headset with the release tab facing
down.
The blue light turns on when the
headset is charging. It may take up to 1
minute for the blue light to turn on.
When the headset is fully charged (about
2 hours), the blue light turns off.
Unplug the charger from the headset.
1
CHARGE YOUR
HEADSET
2
1
To turn on the headset, press and hold the
Call E button on your Bluetooth headset for 5
seconds. The blue light will flash rapidly and
then flash slowly.
To answer or end a call, press the
Call E button on the headset.
To adjust the volume, press the Volume
buttons (shown in step 2) on the headset.
NOTE: The Volume buttons are initially set up
for wearing your headset on your right ear (like
shown in step 2)--with the top button used to
increase volume. You can set which button is
used to increase volume by pressing and
holding the desired Volume button (along with
the Call E button) while turning on the
headset.
To turn off the headset, press and hold the
Call E button on your Bluetooth headset for 5
seconds. The blue light will flash rapidly and
then stop flashing.
PUT YOUR HEADSET
IN PAIRING MODE
CONTINUED
2
Press and hold the Call E button for 6 to 10
seconds until the blue light turns on and
remains on.
NOTE: The blue light will flash as you press
and hold the Call E button. Continue
holding down the Call E button until the
blue light is steadly lit.
NOTE: If you let go of the Call E button
before the blue light is on and steady,
ensure that your headset is off before trying
again (see QUICK TIPS for instructions on
turning off your headset).
2
PUT YOUR HEADSET
IN PAIRING MODE
2
Ensure the headset is powered off (the blue
light is not blinking).
Before you can use your headset, you must pair
(bond) it with your phone.
1
Call Button
Blue Light
Volume
Buttons
TURN ON BLUETOOTH
ON YOUR PHONE AND
PAIR WITH HEADSET
3
Press (Menu) key.
Select Settings.
Select Connection.
Select Bluetooth Link
Select Setup
Scroll to Power and select CHANGE.
Select On.
1
2
3
4
5
Your phone's Bluetooth feature is off by default.
To use your headset, the Bluetooth feature
must be turned on in your phone.
To turn on Bluetooth:
M(
6
TURN ON BLUETOOTH
ON YOUR PHONE AND
PAIR WITH HEADSET
CONTINUED
3
Select BACK.
Select Handsfree.
Select [Look For Devices].
NOTE: Do not select STOP---you will
automatically be taken to the next screen.
Select Motorola HS820.
Select YES to bond.
Enter the passkey 0000 and select OK.
When your headset and phone are
successfully paired, the blue light on your
headset will change from steadly lit to
flashing.
8
9
10
11
12
13
7
Release Tab Down