Moultrie 100 - Manual

C Set to Auto and Wait for
Light to Go Out
DIGITAL GAME CAMERA 100
U S E R M A N U A L
Please take a few minutes
to read and understand these
instructions before using.
GENERAL OPERATION
Your digital game camera can be used two ways.
1) Automatic (AUTO) mode records images using infrared
detection. Use default or custom settings.
2) (HANDHELD) mode records images using manual
operation when circumstances warrant.
NOTE: NEVER OPERATE THE CAMERA WITH
FRONT DOOR OPEN.
SELECT MODE
Press the (MODE) button to scroll between modes. Choose
between two operational modes.
MODE SELECTIONS
(AUTO MODE) - Automatic operation.
(HANDHELD MODE) - Manual operation.
(SETUP MODE) - Used to set Game Camera settings
This screen appears when the camera enters SETUP mode.
Additional menu screens appear as you move through the
SETUP functions. Please refer to (SETTING UP GAME
CAMERA) to identify the different SETUP screen displays.
(TURNING OFF) The unit saves all setup data and turns OFF.
Turning the unit ON & OFF resets the internal systems. This will
not change your settings or erase images.
EVENTS
(MULTIPLE PICTURES PER EVENT) Depending on user settings
the camera may take 1, 2 or 3 pictures per event spaced
approximately 15 seconds apart. If the camera fails to detect
motion after the first detection the camera will still take
subsequent pictures. When capture mode is set to video or the
camera is in (HANDHELD) mode this setting is ignored.
AUTOMATIC FUNCTIONS
(LOW LIGHT OR NIGHT SITUATIONS) The video clip function
will be automatically switched to still photos in low light or night
situations.
NOTE: First still in video will reflect user setup setting.
(DELAY STATUS MENU) During (AUTO) mode, when delay
mode is activated it will be indicated on the LCD
panel as (DLY).
MEMORY ERROR MESSAGES
(MEMORY FULL) Turn off the unit; then turn it back on; when the
unit is turned on it goes directly to the (SETUP) mode; Go to the
(ERASE MEMORY) menu item to delete all the images from the
memory or SD Card.
(SD CARD LOCKED) Turn the unit off; remove the SD card;
unlock it; then insert it; then turn the unit back on.
(SD CARD BAD) Turn the unit off; remove the SD card; insert
a new SD card or clean the contacts; turn the unit back on.
MOUNTING CAMERA
Using mounting straps, mount the
system securely in the desired
location.
LASER AIMING (optional)
If your Game camera is equipped with a laser aiming device,
slide the (POWER ON/OFF/AIM) Switch to the (AIM) position.
Using the laser aim your camera. The red dot indicates the target
area. Note you can also do "Walk" aim in the auto mode.
CAUTION: Looking into laser may be hazardous to the eyes.
Do not stare into beam or aim at other people unnecessarily.
DETECTION
The game camera's infrared sensor will trigger camera when
motion is detected infront of the camera infrared sensor.
AIMING INFRARED SENSOR
If your Game camera is not equipped with a laser aiming
device you can use the systems (INFRARED SENSOR) to
aim your camera. Walk in front of the camera and the Status
Light will flash when you enter the field of view. This
indicates Infrared activation.
Your digital game camera has two
types of memory capacity.
1) Internal memory.
2) Optional SD memory card.
NOTE: Optional SD memory card
will override internal memory.
Maximum card size is 256 MB.
MEMORY CHART
IMPORTANT: Always turn unit off when inserting or
removing a memory card to avoid damage and ensure
that the camera properly updates the memory
information.
SD MEMORY CARD NOT INSTALLED: When the camera is turned
on and an SD memory card is not present, pictures are automatically
stored in the on-board camera memory. The stored images may only
be viewed on a computer or TV connected to the unit.
INSERTING AN SD MEMORY CARD: When an SD memory card is
inserted, any pictures stored in the camera on-board memory
become inaccessible, but are not lost. The user can access these
pictures via the camera USB port when the SD memory card is not
installed.
NOTE: If you get a message (CHECK MEMORY CARD) Your card
may be locked, full or defective and will not work.
TV IMAGE VIEWING
Move the Switch to (ON). Connect unit TV OUT to a VIDEO
IN jack on your TV. Use the (CHANGE) buttons to scroll
through recorded images. Video cable included. TV OUT
works only in (SETUP) mode. All pictures
on memory card can be printed or edited
directly from the card.
CLOCK BATTERY
The small CR2025 button battery powers the clock. It
should be replaced as required.
TURNING THE UNIT ON / OFF
(POWER ON) In the Auto Mode the led flashes for 30
seconds before arming the system. When the LED goes out
the system is working.
2 SETUP • LOAD BATTERY 3 SETUP • MODE SELECTION
8 CAMERA • SPECIFICATIONS
5 OPERATIONS • MOUNTING
OPERATIONS • AIMING LASER
4 SETUP • DEFINITIONS
1 QUICK START
6 MEMORY • CAPACITY & STORAGE 7 CAMERA • DESCRIPTION
Insert a fresh 6Volt/6ah lantern
battery or equivalent. Connect the
Red(+) & Black(-) clips to the battery
and lower the battery hold down
arms. Battery life is about 20 days
depending on temperature and
usage. When B = 20% Replace
battery.
SETUP • PROGRAMMING
SETUP MENU
Press the (MODE) button on the game camera to enter setup.
Press the (CHANGE BUTTONS) to scroll between setting
choices. The feature setting will flash in the LCD until set. Press
the (SELECT BUTTON) to accept settings and move to the next
selection. Programming will rotate between functions until you
exit the SETUP feature.
Press the (SELECT) button, LCD will show month (MM), use
(CHANGE) buttons to set month, press (SELECT) to move to
Day and change to set.
Scroll using the (CHANGE BUTTONS) to choose whether you
would like to reset the number of events counted. Choosing yes
will reset the events back to (00).
Scroll using the (CHANGE BUTTONS) to choose to erase any
stored images on your game camera or optional memory card.
Choosing YES will reset the events back to (00).
Operational Mode Auto or Handheld
Housing Weather-resistant and lockable
Display Liquid Crystal Display (LCD)
LCD Status Display Operating Mode Pictures taken
Pictures left Events
Battery Strength Camera status
Status LED Camera, Flash or IR activity
Sensor 1.3 Megapixel
Built-in Memory Stores pictures or video
Memory Card Up to 256 MB SD card (optional)
Format JPEG - Still pictures, AVI - Video clips
Image Output USB OUT, TV OUT, SD Card
USB Output Requires PC / Windows 2000/ME/XP.
Picture Delay Variable 1 Minute - 60 Minutes
Sequential Delay 15 Seconds between still pictures
Lens Multi element, 10.2mm, F:2.8
Field of View 42°
Focus 4' - Infinity
Infrared Sensor Passive
Infrared Distance 32'
Infrared Width 22°
Flash On, Auto or Off ( Security)
Flash Range 30'
Flash Cycle 15 Seconds
Power Supply 6 Volt Lantern Battery or equivalent
Duty Cycle 20 day average with 6 volt/6 ah battery
Power Connection Alligator clips, red = (+) / black = (-)
Battery Hold Downs Holds battery in place
Clock Battery 3 Volt battery powers LCD Time/Date
Laser Aim (optional) Class 2
Size 7" X 10.25" X 3.5"
Accessories Rechargeable battery, Memory Cards.
WARRANTY
COMPUTER IMAGE VIEWING (Setup Mode Only)
Move the Switch to (ON). Connect unit USB OUT to a USB
jack on the computer.Double click "My Computer"
on the desktop and browse
"removable disk". USB works
only in SETUP mode. All your
images will be stored inside.
Images can be downloaded to
your hard drive. The first image
in the video mode is still and
contains time and date
information for the video clip.
Viewfinder
Shutter Button
(handheld)
Light Sensor
Camera Lens
LCD Status
Display
Lockable
Latch
Weather
Resistant
Housing
Status Light
Mounting
Strap Lug
Infrared
Sensor
Pressure
Equalization Hole
Control Box Latch
SD Memory
Card Slot
USB Out
TV Out
Electronic Flash
Laser (optional)
Mode Button
Power ON/OFF
(AIM optional)
Status Light
Change Buttons
UP Down
Battery Compartment
Battery Connector
( + red )
Battery Connector
( - black )
Weather-Resistant Seal
Battery Hold Down Clips
Select Button (setup)
HANDHELD B=94%
P=OO93/125O
SETUP DATE/TIME
MM/DD/YY HH:MM
AUTO P=OO93/125O
E=3456 B=94% DLY
MODE
MODE
MODE
MODE
EVENTS
BATTERY STRENGTH
Pictures taken
Total pictures
Displays when
camera is
operating
with a delay.
Moultrie Customer Service
(205) 664-6700 or (800) 653-3334
www.moultriefeeders.com
Moultrie Feeders
150 Industrial Rd.
Alabaster, AL 35007
Printed in China
(0905)
This product has been thoroughly tested and inspected before shipment. It is
guaranteed from defects in material and workmanship from the date of
purchase for 1 year. Under this limited guarantee we agree to replace or
repair free of charge any part or parts which have been found to be defective
in original material or workmanship. Should you require in-warranty service,
call our Customer Service Department. If your problem cannot be addressed
over the telephone, we may need you to send us your defective product plus
proof of purchase.
IMPORTANT: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: PC requires
windows 2000/ME/XP.
Use optional card reader to
read images on card.
A
Load Battery and Turn
On Power
B
Set Time and Date
SETUP DATE/TIME
MM/DD/YY HH:MM
MM/
01 to 12
00 to 99
SEL /DD/
01 to 31
SEL
RESET EVENTS
NO SEL YES SEL
Scroll using the (CHANGE BUTTONS) if you wish to set the
camera to its default factory settings.
Scroll using the (CHANGE BUTTONS), Press select to choose
flash setting: (ON), (AUTO), OR (OFF). Security mode = (OFF):
Status light will remain off during this setting.
Scroll using the (CHANGE BUTTONS). Press select to choose
between: (STILL), or (VIDEO).
Scroll using the (CHANGE BUTTONS). Press select to choose
between the image quality choices.
Scroll using the (CHANGE BUTTONS). Press select to choose
between the image quality choices.
Scroll using the (CHANGE BUTTONS). Press select to choose
the number of pictures to be shot in sequence.
Scroll using the (CHANGE BUTTONS).
Press select to set camera's ID number.
You are done with setup. To exit setup,
press the (MODE) button again.
ERASE IMAGES
DEFAULT SETTINGS
NO SEL YES SEL
NO SEL YES SEL
IMAGE MODE
STILL SEL VIDEO SEL
IMAGE QUALITY
STANDARD SEL HIGH SEL
FLASH
ON SEL OFF AUTO
SEL
HH:
00 to 23
SEL :MM
00 to 59
SEL SEL
/YY
00 to 35
SEL
IMAGE DELAY
1 MIN SEL 5 MIN
3O MIN 6O MIN SEL
1O MIN SEL
1-SHOT SEL 2-SHOT 3-SHOT SEL
SEL
(SECURITY)
CAMERA ID OO MODE
MULTI-IMAGE
LASER RADIATION
DO NOT STARE INTO BEAM
DIODE LASER
1mW MAX OUTPUT at 650 nm
CLASS II LASER PRODUCT
CAUTION
Laser Classification
Class II Laser Product
Wavelength: 650nm
Maximum Output: < 1mW
Product complies with applicable
requirements of 21 CFR 1040.10
and 1040.11
OPERATIONS • INFRARED SENSOR
OPERATIONS • IMAGE VIEWING
Image Optional 256 MB Card
Standard 640 x 480 = 2,320 pics.
High Res 1280 x 1024 = 608 pics
Video Clips 10 frames per sec. = 288
Image Internal Memory
Standard 640 x 480 = 100 pics.
High Res 1280 x 1024 = 24 pics
Video Clips 10 frames per sec. = 9
3 3
EASY STEPS EASY STEPS
and you are ready to go!
6328 Oleatha Avenue
St. Louis, Missouri 63139
Tel. & Fax: (314) 352-1671
email: [email protected]
Graphic Artist: Robert Curran
Client: MOULTRIE FEEDERS
Job Number: MF1010
File name: DGC_instructions_cra_r8.ai8
Date Created: 5.23.05 revised 9.5.05
Date Approved:
Job Description:
Digital Game Camera 100 series
Job Type: Instructions
Printer:
Printing Specifications:
Process
100% - K
DIELINE
DOES NOT PRINT
CROP MARKS CROP MARKS
Photography: All images print as final art
Paper stock: Standard white stock
Final size:
3.5" (w) x 2.83" (h)
Coating: n/a
LPI: 175
MFHDGC_INSTRUCTIONS_INSIDE SPREAD_8.26.05
MFHDGC_INSTRUCTIONS_EXTERIOR SPREAD_8.26.05
Image capacity is based on average use and will vary.