Maxxsonics SS750.1 - Manual (Page 5)

AMPLIFIER FEATURE DESCRIPTIONS
SUPER SPORT AMPLIFIERS:
3
LINE INPUT: Accepts unbalanced RCA inputs from 0.2 volts to 9 volts.
LINE OUTPUT: The unbalanced RCA outputs are set the same as the CROSSOVER
switch on he top mount control.
BALANCED INPUT: Accepts balanced line inputs from 0.4 volts to 12 volts for the
optional MMBLD-1 balanced line driver.
LEVEL: The input level control allows you to match the amplifier input sensitivity to the
output level of the RADIO/CD source from 0.2 volts to 9 volts when using unbalanced
(RCA) and 0.2 volts to 18 volts with the balanced input.
PHASE: The Phase shift is fully adjustable from 0 to 180 degrees.
REMOTE: The RJ45 Remote jack accepts the Bass Remote Module.
BASS EQ: The Bass Boost is fully adjustable from 0 to 18db at 45Hz.
SUBSONIC: The variable Subsonic filter is fully adjustable from 15Hz to 35Hz.
LOWPASS: The built-in low pass frequencies are fully variable from 35 to 250Hz.
POWER: Indicates that the amp has power, ground and remote turn-on input via a green
L.E.D.
PROTECT: Indicates that the amplifier has detected a fault and will not operate. There
are several possible problems that can cause the amplifier to go into the protect mode.
See the
trouble shooting guide in the back of the manual for details.
LINE INPUT: Accepts unbalanced RCA inputs from 0.2 volts to 9 volts.
LINE OUTPUT: The unbalanced RCA outputs are set the same as the CROSSOVER
switch on he top mount control.
BALANCED INPUT: Accepts balanced line inputs from 0.4 volts to 12 volts for the
optional MMBLD-1 balanced line driver.
LEVEL: The input level control allows you to match the amplifier input sensitivity to the
output level of the RADIO/CD source from 0.2 volts to 9 volts when using unbalanced
(RCA) and 0.2 volts to 18 volts with the balanced input.
PHASE: The Phase shift is fully adjustable from 0 to 180 degrees.
REMOTE: The RJ45 Remote jack accepts the Bass Remote Module.
BASS EQ: The Bass Boost is fully adjustable from 0 to 18db at 45Hz.
SUBSONIC: The variable Subsonic filter is fully adjustable from 15Hz to 35Hz.
LOWPASS: The built-in low pass frequencies are fully variable from 35 to 250Hz.
POWER: Indicates that the amp has power, ground and remote turn-on input via a green
L.E.D.
PROTECT: Indicates that the amplifier has detected a fault and will not operate. There
are several possible problems that can cause the amplifier to go into the protect mode.
See the
trouble shooting guide in the back of the manual for details.
MASTER / SLAVE: This mono amplifier allows you to electronically “link” two amps
together so that you can power a single subwoofer with two amplifiers.
The mono amps are capable of 4, 2 & 1-Ohm loads.
Operating the amp below 1-Ohm can cause damage to
The mono amps are capable of 4, 2 & 1-Ohm loads.
Operating the amp below 1-Ohm can cause damage to
SS1000.1D / SS1500.1D 1-CHANNEL MONO AMPLIFIERS
SS1900.1D 1-CHANNEL MONO AMPLIFIERS
L
R
L
R
9V 0.2V 0 180 0dB 12dB 15 35Hz 35 250Hz PRO
INPUT OUTPUT BALANCED LEVEL PHASE REMOTE BASS EQ SUBSONIC LOW PASS PWR
INPUT
L
R
L
R
IN
OUT
9V 0.2V 0 180 0dB 12dB 15 35Hz 35 250Hz PRO OUTPUT MASTER
INPUT
SLAVE
INPUT OUTPUT BALANCED LEVEL PHASE REMOTE BASS EQ SUBSONIC LOW PASS PWR
INPUT