Jonsered 2045 - Manual (Page 34)

34
– English
Engine
Cylinder volume, cu.in/cm 3
Cylinder bore, inch/mm
Stroke, inch/mm
Idle speed, rpm
Power, kW/rpm
Ignition system
Manufacture
Type of ignition system
Spark plug
Electrode gap, inch/mm
Fuel and lubrication
system
Manufacturer
Carburetor type
Fuel capacity, US pint/litre
Oil pump capacity at
6000 rpm, ml/min
Oil capacity, US pint/litre
Type of oil pump
Weight
Without bar and chain, Lbs/kg
Chain/bar
Standard bar length, inches/cm
Recommended bar lengths,
inches/cm
Usable cutting length,
inches/cm
Chain speed at max.power,
m/sec
Pitch, inches/mm
Thickness of drive link,
inch/mm
Number of teeth on drive
sprocket
2045
2,67/44
1,65/42
1,26/32
2 500
2,2/ 9 000
Phelon
CD
Champion
RCJ 7Y
NGK
BPMR 7A
0,02/0,5
Zama
C IQ-EL5
1,06/0,5
6,0
0,53/0,25
Automatic
10,3/4,7
15/38
13-20/33-50
12-19/31-48
17,3
0,325"/8,25
0,050"/1,3
0,058"/1,5
7
2050
3,0/49
1,73/44
1,26/32
2 500
2,3/ 9 000
Phelon
CD
Champion
RCJ 7Y
NGK
BPMR 7A
0,02/0,5
Zama
C IQ-EL5
1,06/0,5
6,0
0,53/0,25
Automatic
10,3/4,7
15/38
13-20/33-50
12-19/31-48
17,3
0,325"/8,25
0,050"/1,3
0,058"/1,5
7
Recommended original and replacement bar
and chain combinations
Following is a list of recommended cutting equipment for
the Jonsered chain saw models 2045 and 2050. The
combinations of power head, bar and chain have been
investigated in accordance with the kickback and vibration
requirements of ANSI B 175.1–1991.
The guide bar nose radius is determined by either the
maximum number of teeth in the nose sprocket or the
corresponding maximum nose radius of a solid bar.
The following list is the chain saw manufacturers
recommendations. There may be other combinations
available, which will also achieve kickback protection.
As we are listing the maximum guide bar nose radius, you
may use a guide bar with smaller nose radius than in our
list. For guide bars of the same length, all sprocket-nose
guide bars of the same pitch and having the same number
of sprocket teeth may be considered to have equivalent
kickback energy. A hard nose bar having the same length
and nose radius as a sprocket-bar may be considered to
have equivalent or less kickback energy than the sprocket-
nose bar.
Low kickback saw chain is a chain which has only met the
kickback performance requirements of ANSI B 175.1 safety
requirements for gasoline powered chain saws when
tested on the representative sample of chain saws below
3.8 cu. in. specified in ANSI 175.1. We recommend that
you as a replacement use the listed chains or "Low
kickback saw chains" which are available at your dealer.
Guide bar Saw chain
Length Pitch Max nose
inch inch radius
13 0,325 10T Jonsered S30 or Oregon 95VP
15 0,325 10T or Total/Sabre 528PS
16 0,325 10T
18 0,325 10T
15 0,325 10T Jonsered S25 or Oregon 21VB
16 0,325 10T
18 0,325 10T
20 0,325 12T
TECHNICAL DATA
0,058"/1,5mm – S25 21VB 528PS
0,050"/1,3mm S30, 95VP – 20VB 520PS
Note: For the chains above you are free to choose between 0,050" and
0,058" gauge drive link for the corresponding bar, see the table below.
´*xmQ¶5%¨