JVC SR MV45U - Manual (Page 61)

Masterpage:Right+
EN
61
Filename [SR-MV45_55U_11Subsidiary.fm]
Page 61 January 10, 2007 1:18 pm
SUBSIDIARY SETTINGS
8 PICTURE CONTROL — AUTO / EDIT / SOFT / SHARP
This feature helps you to adjust the playback picture quality
according to your preference. Normally select “AUTO”.
AUTO : Picture quality is adjusted automatically.
EDIT : Minimizes picture degradation during editing (recording and
playback).
SOFT : Reduces image coarseness when viewing overplayed tapes
containing a lot of noise.
SHARP : Clearer, sharper-edged picture when viewing images with
lots of flat, same-colored surfaces such as cartoons.
NOTES:
● When you select “EDIT”, “SOFT” or “SHARP”, the selected mode will
not change until you select another mode.
● When you select “EDIT” to dub tapes, be sure to select “NORM” after
you finish dubbing the tapes.
● When “VIDEO CALIBRATION” is “OFF”, “PICTURE CONTROL”
switches automatically from “AUTO” to “NORM”.
8 VIDEO STABILIZER — ON / OFF
When this function is set to “ON”, you can automatically correct
vertical vibration in the picture when playing back unstable
recordings made on another recorder.
NOTES:
● When you finish viewing a tape, be sure to set this function to “OFF”.
● Regardless of the setting, this function has no effect during recording
and during special effects playback.
● The on-screen display may jitter vertically when this function is set to
“ON”.
● To watch recordings with close-caption, set this function to “OFF”.
8 SUPERIMPOSE — AUTO / ON / OFF
When this function is set to “AUTO”, various operational indicators
appear on the TV screen.
AUTO : To superimpose operational indications for approximately
five seconds just after the corresponding operation.
ON : Functions in the same way as “AUTO”. However, when “ON” is
selected, the counter display ( ੬ pg. 14) will always be displayed
during playback.
OFF : To turn off superimposed indications.
NOTES:
● When you use this unit as the source player for editing, be sure to set
“SUPERIMPOSE” to “OFF” before starting.
● During playback, the operation mode indicators may be disturbed
depending on the type of tape being used.
8 DIGITAL R3 — ON / OFF
When this function is set to “ON”, the Digital 3R picture system
applies edge correction to the luminance signal to enhance detail.
NOTES:
● Normally it is recommended to keep “DIGITAL 3R” set to “ON”.
● Depending on the type of tape being used, picture quality may be
better with “DIGITAL 3R” set to “OFF”.
● If you use the unit as the source player for editing, be sure to set
“DIGITAL 3R” to“OFF” before starting.
8 BLUE BACK — ON / OFF
When this function is set to “ON”, the TV screen becomes all blue
when there is no signal input from the external input.
NOTE:
When you want to receive an unstable
external input with poor signals,
set this function to “OFF”.
8 S-VHS MODE — ON / OFF
Your unit can record in S-VHS (Super VHS), S-VHS ET or VHS.
To record in S-VHS:
Set “S-VHS MODE” to “ON”. Then, insert a cassette marked
“S-VHS”. The S-VHS indicator lights up on the front display panel.
The S-VHS recording mode is selected.
To record in S-VHS ET on a VHS cassette:
Set “S-VHS ET” to “ON”. (
੬ pg. 60) Then, insert a cassette
marked “VHS”. The S-VHS indicator lights up on the front display
panel.
To record in VHS:
Insert a cassette marked “VHS”.
Set “S-VHS ET” to “OFF”. (
੬ pg. 60)
The VHS recording mode is automatically selected regardless of
the “S-VHS MODE” setting.
To record in VHS on an S-VHS cassette:
Insert a cassette marked “S-VHS”. The S-VHS indicator lights up
on the front display panel. Then, set “S-VHS MODE” to “OFF”. The
S-VHS indicator goes off.
The VHS recording mode is selected.
NOTE:
When playing back a tape that has been recorded in S-VHS or
S-VHS ET, the S-VHS indicator lights up on the front display panel
regardless of the “S-VHS MODE” setting.
8 RETURN POINT — TAPE END / REC END
Returning point for Playback or Repeat Play can be set to tape end
or recording end. (This unit considers 1-second unrecorded portion
as the recording end.) When the returning point is reached,
playback stops and the cassette will be automatically rewound.
TAPE END : Playback stops at the end of tape.
REC END : Playback stops at the end of the recording.
NOTE:
The setting you have made is kept in memory. Even if this unit is
unplugged or power failure occurs, it will resume every time you turn on
this unit. (
੬ pg. 65)
8 REC SAFETY — ON / OFF
Usually, you can only record onto a cassette with its record safety
tab intact. When this function is set to “OFF”, recording can be
done onto a cassette with its record safety tab removed.
NOTES:
● The setting you have made is kept in memory. Even if this unit is
unplugged or power failure occurs, it will resume every time you turn
on this unit. (
੬ pg. 65)
● When “REC SAFETY” is set to “OFF”, playback does not start
automatically when you insert a cassette with its record safety tab
removed. (
੬ pg. 36)
SR-MV45_55US.book Page 61 Wednesday, January 10, 2007 1:18 PM