Sony ECM S80 User Manual

Electret condenser microphone, Ecm-s80, Bc e f

Advertising
background image

A

Operating Instructions

Mode d’emploi

Bedienungsanleitung

Manual de instrucciones

Istruzioni per l’uso

(facciata opposta)

Manual de instruções

(no verso)

Electret Condenser
Microphone

3-241-661-11 (1)

ECM-S80

Sony Corporation © 2002 Printed in Japan

Before operating the unit, please read this manual thoroughly
and retain it for future reference.

Features

• Thin and lightweight portable microphone
• Cord can be retracted and stored in the microphone for ease of

portability

• Two-way power system (plug-in power or battery)

Installing the battery

(See fig. A)

1 Open the battery compartment

Push the hook to the left using a pointed object, such as a
ballpoint pen, and pull out the battery compartment.

2 Insert a new battery with the

e

end up.

Make sure that the e and E end is in the correct direction.
Otherwise, the microphone cannot be powered.

Removing the battery (See fig. B)

Push the battery up from underneath.

Battery life
When you turn the power on, the battery check indicator should
light momentarily. If the battery is weak, the indicator lights
dimly or does not light at all. In this case, replace the battery
with a new one. (See fig. C)
A new alkaline battery allows continuous operation of the
microphone for about 80 hours. To avoid battery wear or
leakage, be sure to turn the power off after using the
microphone.

How to use

Parts Identification (See fig. D)

1

Cord retracting wheel

2

POWER switch

When the microphone is powered by plug-in power, turn its
own power off.

3

Battery check indicator

4

Microphone

5

Stereo miniplug

To the microphone jack of the recording equipment

6

Slide

Direct the microphone towards the sound
source (See fig.
E)

Note

To avoid to noisy recordings, make sure that noise does not
occur where the microphone is placed (for example, an air-
conditioner above the microphone).

To pull out the stereo miniplug cord
(See fig.
F)
Press and hold the slide, and then pull out the cord.

To roll up and store the stereo miniplug
cord (See fig.
F)
Turn the cord retracting wheel in the direction of the arrow to
retract the cord into the microphone.

Notes

• If you turn the cord retracting wheel in the opposite direction,

damage may result.

• When you retract or pull out the cord, you may feel friction. In

this case, retract or pull the cord again after you pull or retract
it completely.

Precautions

• This microphone is a precision instrument. Never

disassemble.

• Keep the microphone away from extremely high temperatures

(above 60°C or 140°F) and humidity.

• If the microphone is placed near speakers, a high pitched

noise may be heard (acoustic feedback). This is caused by the
microphone catching sound from the speakers repeatedly.
In this case, place the microphone as far as possible from the
speakers, or turn down the volume of the speakers.

• When using outdoors, never let the microphone become wet

with rain or saltwater.

D

English

Français

Deutsch

Troubleshooting

There is no sound.
• The e and E ends of the battery may not be installed in the

correct direction.

,

Make sure the e and E ends of the battery are in the
correct direction.

There is no sound or interfere (noise).
• The Battery may be weak.

When you turn the power on after turning the power off, the
battery check indicator lights dimly or does not light at all.

,

If the battery check indicator lights dimly or does not
light at all, it means that the battery is weak or dead.
Replace the battery with a new one.
Clean the stereo miniplug with a soft cloth.

The battery check indicator lights
momentarily.
• This is not a malfunction.

This indicates the battery’s remaining life. If the battery
becomes weak, the battery check indicator lights dimly or
does not light at all.

Specifications

Type

Electret condenser microphone

Cord

ø 2.2 mm (

3

/

32

in.) OFC litz cord

(2 core shielded)
Length: Approx. 70 cm (27

5

/

8

in.)

Attached with gold plated L-shaped stereo
miniplug

Power source 2 way power supply system

plug-in power
alkaline manganese battery LR44 (1)

Dimensions

Approx. 54

Ч

11

Ч

86 mm (w/h/d)

(2

1

/

4

Ч

7

/

16

Ч

3

1

/

2

in.)

Mass

Approx. 39 g (1 oz.)

(including battery)

Frequently response

100 – 10,000 Hz

Directivity

Unidirectional

×

2

Output impedance

1.6 k

± 30%

Sensitivity

Open circuit output voltage level –40 ± 4 dB/Pa
0 dB = 1 V / Pa, 1,000 Hz
(1 Pa = 10µ bar = 94 dB

SPL

)

Battery life

Approx. 80 hours (continuous operation)

Operating temperature range

0°C – 40°C (32°F – 104°F)

Design and specifications are subject to change without notice.

1

2

One alkaline manganese
battery LR44

Pile alcaline au
manganèse LR44

Eine Alkali-Mangan-
Batterie LR44

Alkaline manganese battery
Pile alcaline au manganèse
Alkali-Mangan-Batterie

3

end

Polarité

3

Seite

3

#

end

Polarité

#

Seite

#

ON

POWER

PLUG IN POWER

OFF

1

2

3

4

5

6

B

C

E

F

Avant la mise en service de cet appareil, prière de lire
attentivement ce mode d’emploi et de le conserver pour toute
référence future.

Caractéristiques

• Microphone portable mince et léger
• Le cordon peut se rétracter et être rangé à l’intérieur du

microphone pour que celui-ci soit plus facile à transporter.

• Double système d’alimentation (alimentation à l’enfichage ou

sur pile)

Mise en place de la pile

(Voir fig. A)

1 Ouvrez le logement de la pile.

Poussez l’ergot vers la gauche à l’aide d’un objet pointu,
comme un stylo à bille, puis sortez le logement de la pile.

2 Insérez une pile neuve avec la polarité

e

dirigée

vers le haut.

Vérifiez que les polarités e et –E sont bien placées.
Sinon le microphone ne sera pas alimenté.

Retrait de la pile (Voir fig. B)

Poussez la pile par-dessous.

Autonomie de la pile
Lorsque vous mettez l’appareil sous tension, le témoin de pile
s’allume un instant. Si la pile est faible, le témoin s’allume
faiblement ou ne s’allume pas du tout. Dans ce cas, remplacez la
pile. (Voir fig. C)
Une pile alcaline neuve permet d’utiliser le microphone en
continu pendant environ 80 heures. Veillez à couper
l’alimentation après avoir utilisé le microphone afin d’éviter
toute usure ou toute fuite de la pile.

Utilisation

Nomenclature (Voir fig. D)

1

Molette de rétraction du cordon

2

Commutateur POWER

Lorsque le microphone est alimenté par une alimentation à
l’enfichage, mettez-le hors tension.

3

Témoin de pile

4

Microphone

5

Minifiche stéréophonique

Vers la prise microphone de l’appareil d’enregistrement

6

Bouton coulissant

Dirigez le microphone vers la source sonore
(Voir fig.
E)

Remarque

Pour que l’enregistrement ne soit pas parasité, assurez-vous
qu’aucun bruit ne se produit lorsque le microphone est installé
(par exemple un climatiseur au-dessus du microphone).

Pour sortir le cordon de la minifiche
stéréophonique
(Voir fig.
F)
Appuyez sur le bouton coulissant et maintenez-le enfoncé puis
tirez le cordon.

Pour enrouler et ranger le cordon de la
minifiche stéréophonique (Voir fig.
F)
Tournez la molette de rétraction du cordon dans le sens de la
flèche pour enrouler le cordon dans le microphone.

Remarques

• Si vous tournez la molette de rétraction du cordon dans l’autre

sens, vous risquez de l’endommager.

• Il est possible que vous sentiez un frottement lorsque vous

enroulez ou déroulez le cordon. Dans ce cas, enroulez ou
déroulez de nouveau le cordon après l’avoir déroulé ou
enroulé complètement.

Précautions

• Ce microphone est un instrument de précision. Ne jamais le

démonter.

• Ne pas exposer le microphone à des températures

extrêmement élevées (au-dessus de 60°C ou 140°F) ou à
l’humidité.

• Si le microphone se trouve à proximité d’enceintes, un son

très aigu risque d’être audible (effet Larsen) car le microphone
capte à plusieurs reprises le son des enceintes. Dans ce cas,
placez le microphone aussi loin que possible des enceintes ou
réduisez le volume des enceintes.

• Ne jamais laisser mouiller le microphone par la pluie ou l’eau

de mer s’il est utilisé en extérieur.

Dépannage

Il n’y a aucun son.
• Il est possible que les polarités e et E de la pile ne soient pas

dans le bon sens.

,

Vérifiez que les polarités e et E de la pile sont dans le
bon sens.

Il n’y a aucun son ni interférence (parasites).
• Il est possible que la pile soit faible.

Lorsque vous mettez l’appareil sous tension après l’avoir mis
hors tension, le témoin de pile s’allume faiblement ou ne
s’allume pas du tout.

,

Si le témoin de pile s’allume faiblement ou ne s’allume
pas du tout, la pile est faible ou vide. Remplacez-la par
une pile neuve.
Nettoyez la minifiche stéréophonique avec un chiffon
doux.

Le témoin de pile s’allume un instant.
• Il ne s’agit aucunement d’un dysfonctionnement.

Ceci indique l’autonomie de la pile. Si elle devient faible, le
témoin de pile s’allume faiblement ou ne s’allume pas du tout.

Spécifications

Type

Microphone à électret

Cordon

ø 2,2 mm (

3

/

32

po.) Cordon litz OFC (blindage 2

fils)
Longueur : Env. 70 cm (27

5

/

8

po.)

Fixé avec une minifiche stéréophonique en L
plaquée or

Source d’alimentation

2 système d’alimentation

alimentation à l’enfichage
pile alcaline au manganèse LR44 (1)

Dimensions

Env. 54

Ч

11

Ч

86 mm (l/h/p)

(2

1

/

4

Ч

7

/

16

Ч

3

1

/

2

po.)

Poids

Env. 39 g (1 on.) (Pile comprise)

Réponse en fréquence

100 – 10 000 Hz

Directivité

Unidirectionnel

×

2

Impédance de sortie

1,6 k

± 30%

Sensibilité

Niveau de la tension de sortie en circuit ouvert
–40 ± 4 dB/pa.
0 dB = 1 V / Pa, 1 000 Hz
(1 Pa = 10µ bar = 94 dB

SPL

)

Autonomie de la pile

Env. 80 heures (en utilisation continue)

Plage de température de fonctionnement

0°C – 40°C (32°F – 104°F)

La conception et les spécifications sont sujettes à modifications sans
préavis.

Lesen Sie diese Anleitung vor der Inbetriebnahme genau durch,
und bewahren Sie sie zum späteren Nachschlagen sorgfältig auf.

Besondere Merkmale

• Dünnes und leichtes tragbares Mikrofon
• Zum bequemen Tragen läßt sich das Kabel einziehen und im

Mikrofon unterbringen.

• Zwei Möglichkeiten zur Stromversorgung (Plug-in-Power

oder Batterie)

Einlegen der Batterie

(siehe Abb. A)

1 Öffnen Sie das Batteriefach.

Drücken Sie den Haken mit einem spitzen Gegenstand wie
z. B. einem Kugelschreiber nach links, und ziehen Sie das
Batteriefach heraus.

2 Legen Sie eine neue Batterie mit der Seite

e

nach

oben ein.

Achten Sie darauf, daß die Seiten e und E richtig eingelegt
sind. Andernfalls wird das Mikrofon nicht mit Strom
versorgt.

Herausnehmen der Batterie
(siehe Abb.
B)

Drücken Sie die Batterie von unter her nach oben.

Lebensdauer der Batterie
Wenn Sie das Gerät einschalten, sollte die Batterieanzeige kurz
aufleuchten. Wenn die Batterie schwach ist, leuchtet die
Anzeige weniger hell oder gar nicht mehr. Tauschen Sie die
Batterie in diesem Fall gegen eine neue aus (siehe Abb. C).
Eine neue Alkalibatterie reicht bei kontinuierlichem Betrieb des
Mikrofons etwa 80 Stunden. Um eine unnötige Belastung der
Batterie zu vermeiden, schalten Sie das Mikrofon nach
Gebrauch bitte immer aus.

Gebrauch

Bezeichnung der Teile (siehe Abb. D)

1

Kabelaufwickelscheibe

2

Schalter POWER

Wenn das Mikrofon über Plug-in-Power mit Strom versorgt
wird, schalten Sie es hier aus.

3

Batterieanzeige

4

Mikrofon

5

Stereoministecker

an die Mikrofonbuchse des Aufnahmegeräts

6

Schieber

Richten Sie das Mikrofon auf die Tonquelle
(siehe Abb.
E)

Hinweis

Um Aufnahmen mit starken Nebengeräuschen zu vermeiden,
achten Sie auf eine ruhige Umgebung um das Mikrofon
(beispielsweise sollte sich über dem Mikrofon keine
Klimaanlage befinden).

So ziehen Sie das Kabel mit dem
Stereoministecker heraus
(siehe Abb.
F)
Halten Sie den Schieber gedrückt, und ziehen Sie das Kabel
heraus.

So wickeln Sie das Kabel mit dem
Stereoministecker zum Verstauen wieder
auf (siehe Abb.
F)
Drehen Sie die Kabelaufwickelscheibe in Pfeilrichtung, um das
Kabel in das Mikrofon einzuziehen.

Hinweise

• Wenn Sie die Kabelaufwickelscheibe in die andere Richtung

drehen, kann es zu Schäden kommen.

• Wenn beim Aufwickeln bzw. Herausziehen des Kabels ein

Widerstand zu spüren ist, ziehen Sie das Kabel zunächst
vollständig heraus und wickeln es dann auf bzw. wickeln Sie
es vollständig auf und ziehen es dann heraus.

Zur besonderen Beachtung

• Das Mikrofon besteht aus Präzisionsteilen. Lassen Sie es

niemals fallen.

• Halten Sie das Mikrofon von hohen Temperaturen (über

60°C) fern.

• Wenn sich das Mikrofon in der Nähe von Lautsprechern

befindet, kann ein hoher Ton zu hören sein. Dies wird dadurch
hervorgerufen, daß das Mikrofon den Ton von den
Lautsprechern wiederholt aufnimmt. Stellen Sie das Mikrofon
in einem solchen Fall möglichst weit entfernt von den
Lautsprechern auf. Oder verringern Sie die Lautstärke der
Lautsprecher.

• Achten Sie bei Außenaufnahmen darauf, daß das Mikrofon

nicht naß wird. Schützen Sie es vor Regen und Salzwasser.

Störungsbehebung

Es ist kein Ton zu hören.
• Die Seiten e und E der Batterie wurden möglicherweise

falsch herum eingelegt.

,

Vergewissern Sie sich, daß die Seiten e und E der
Batterie richtig herum eingelegt sind.

Es ist kein Ton oder Interferenzen (Störungen)
zu hören.
• Die Batterie ist möglicherweise zu schwach.

Wenn Sie das Mikrofon aus- und wieder einschalten, leuchtet
die Batterieanzeige schwach oder gar nicht.

,

Wenn die Batterieanzeige weniger hell oder gar nicht
leuchtet, heißt das, daß die Batterie schwach oder
erschöpft ist. Ersetzen Sie sie durch eine neue.
Reinigen Sie den Stereoministecker mit einem weichen
Tuch.

Die Batterieanzeige leuchtet kurz.
• Dies ist keine Fehlfunktion.

Damit wird die Restkapazität der Batterie angegeben. Wenn
die Batterie schwächer wird, leuchtet die Batterieanzeige
weniger hell oder gar nicht mehr.

Technische Daten

Typ

Elektret-Kondensatormikrofon

Kabel

ø 2,2 mm OFC-Litze (beide Leiter geschirmt)
Länge: ca. 70 cm
Mit vergoldetem L-förmigem Stereoministecker

Stromversorgung

2 Möglichkeiten zur Stromversorgung
Plug-in-Power
Alkali-Mangan-Batterie LR44 (1)

Abmessungen ca. 54

Ч

11

Ч

86 mm (B/H/T)

Gewicht

ca. 39 g (mit Batterie)

Frequenzgang 100 – 10 000 Hz
Richtcharakteristik

Keule

×

2

Ausgangsimpedanz

1,6 k

± 30 %

Empfindlichkeit

Leerlauf-Ausgangspegel –40 dB ± 4 dB/Pa
0 dB = 1 V/Pa, 1 000 Hz
(1 Pa = 10µ bar = 94 dB

SPL

)

Batterie-Lebensdauer

ca. 80 Stunden (kontinuierlicher Betrieb)

Betriebstemperatur

0 °C – 40 °C

Änderungen, die dem technischen Fortschritt dienen, bleiben
vorbehalten.

WALKMAN

*

, etc.

WALKMAN

*

etc.

WALKMAN

*

usw.

*

WALKMAN is a registered trademark of
Sony Corporation.

*

WALKMAN est une marque déposée de
Sony Corporation.

*

WALKMAN ist ein eingetragenes
Warenzeichen der Sony Corporation.

Advertising