Sony XCL-U1000C - Manual

3-863-302-01 (1)
 2004 Sony Corporation Printed in Japan
XCL-U1000C/ U1000
•
•
•
Operating Instructions
D C
•
•
•
•
•
1 1
Owner’s Record
The model and serial numbers are located on the bottom.
Record the serial number in the space provided below.
Refer to these numbers whenever you call upon your Sony
dealer regarding this product.
Model No. _____________ Serial No. ______________
IMPORTANT
The nameplate is located on the bottom.
For the customers in the U.S.A.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly
approved in this manual could void your authority to operate this
equipment.
The shielded interface cable recommended in this manual must be
used with this equipment in order to comply with the limits for a digital
device pursuant to Subpart B of Part 15 of FCC Rules.
If you have any questions about this product, you may call:
Sony's Business Information Center (BIC) at 1-800-686-SONY (7669)
or Write to: Sony Customer Information Services Center
6900-29 Daniels Parkway, PMB 330
Fort Myers, Florida 33912
Declaration of Conformity
Trade Name: SONY
Model No.: XCL-U1000C
XCL-U1000
Responsible Party: Sony Electronics Inc.
Adress: 16450 W. Bernardo Dr, San Diego, CA 92127
U.S.A.
Telephone No.: 858-942-2230
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Note: This camera is not intended for use in security applications in the
meaning of the European standard series EN 50132 (Alarm systems -
CCTV surveillance systems for use in security applications).
A
B
English
A
1 2 DIGITAL IF
3 DC IN 4 RS-232C
1 2 PC
3 4
5 DC-700 6 PC
DC+12 V
• 0 40
•
•
XCL-U1000C/U1000 LVDS
XCL-U1000C
XCL-U1000
15
UXGA 200 CCD
CCD
•
• :
•
• :
•
•
•
• XCL-U1000C
• XCL-U1000C
1/15 1/10000
1
XCL-U1000
2 2
CCD
XCL-U1000C
B
XCL-U1000C/U1000
1
CCD
2 CCXC-12P02N 2 m /05N 5 m /10N 10 m /
25N 25 m
DC IN
3 C
4 DC-700
AC
5 VCT-ST70I
6
PC PCI
7 1MA26-4560-OSC-200 2 m /500 5 m /
A00 10 m
C
DC-700
DC-700
DC-700 DC-700
1 C 1 DC IN
2 CCXC-12P05N 2 CAMERA
3 TRIG 3 AC IN
4 AC
C
WARNING
To prevent fire or shock hazard, do not expose
the unit to rain or moisture.
To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel
only.
/ Camera
When installing the camera Fig. A
When you install the camera with various peripheral devices and if the
devices have different ground electric potential, ground only one device. In
case there is an ground electric potential difference, the camera may be
damaged.
1 Monitor output connector 2 Digital interface connector
3 DC IN connector 4 RS-232C connector
1 Monitor 2 Host device (e.g., PC)
3 Abnormal electricity 4 Ground electric potential difference
5 Power supply unit 6 Camera control device (e.g., PC)
(DC-700/700CE)
Notes on Operation
Power supply
The camera operates on +12 V DC. Use a stable power source free from
ripple or noise.
Foreign bodies
Be careful not to spill liquids, or drop any flammable or metal objects in the
camera body.
Locations for operation and storage
Avoid operation or storage in the following places.
• Extremely hot or cold locations. Recommended temperature range is 0°C
to 40°C. (32°F to 104°F)
• Locations subject to strong vibration
• Near generators of strong electromagnetic radiation such as TV or radio
transmitters.
Care
Use a blower to remove dust from the surface of the lens or optical filter.
Clean the exterior with a soft, dry cloth.
If the camera is very grimy, apply a cloth soaked in a mild detergent then
wipe with a dry cloth. Do not apply organic solvents such as alcohol or
benzine which may damage the finish.
Overview
Before operating the unit, please read this manual thoroughly and retain for
future reference.
The XCL-U1000C/U1000 is a digital video camera module. This camera
module outputs digital images utilizing LVDS via the digital interface
connector.
XCL-U1000C: Color Digital Video Camera Module
XCL-U1000: Black-and-White Digital Video Camera Module
Digital interface connector
Equipped with a Camera Link compatible connector. The XCL-U1000C/
U1000 can output a digital image at 15 frames per second.
High image quality
The XCL-U1000C/U1000 (UXGA) has a progressive scan CCD of
2,000,000 pixels. Both cameras produce high-resolution images. By
adopting square pixels, images can be processed using the original aspect
ratio without a converting procedure.
Various mode settings
Sending a command from the host device allows the following mode
settings.
• Gain
• Read mode: normal /binning
• High rate scan
• Shutter: Normal/Trigger shutter
• Shutter speed
• Gamma
• Detail
• White balance (XCL-U1000C only)
• Matrix (XCL-U1000C only)
Electronic shutter function
Shutter speed can be selected from variety of available speeds.
External trigger shutter function (1/15 to 1/10000 sec.)
You can obtain a freeze picture by inputting an external trigger. This
function is useful to shoot a fast-moving object clearly.
High rate scan
The camera module can limit the number of effective video output lines to
achieve high frame rates, enabling high-speed image processing.
Binning (XCL-U1000 only)
By “binning” two pixels that align vertically, you can acquire a frame rate
twice as high as that in the normal mode.
Body fixing
The screw holes to install the camera module are located under the front
panel (the CCD reference plane). Installing the camera module on the front
panel minimizes deviation of the optical axis.
Matrix (XCL-U1000C only)
Utilizing the matrix unit reproduces color more accurately.
Detail
The camera module can accentuate all the edges of an image producing
sharper detail.
System Components Fig. B
The Video Camera Module XCL-U1000C/U1000 system comprises the
following optional products (available separately).
1 Video Camera Module
This is a small-size, high-resolution, video camera module using a
progressive scan CCD image sensor.
2 CCXC-12P02N (2 m, 6.6 ft)/05N (5 m, 16.4 ft)/10N (10 m, 32.8 ft)/
25N (25 m, 82 ft) camera cable
This is attached to the DC IN connector of the camera module and is used
for power supply and exchange of trigger signals.
3 C-mount lens
Use a high-resolution lens.
4 DC-700/700CE camera adaptor
This is connected to the camera module to enable power supply from
ordinary AC power source.
5 VCT-ST70I tripod adaptor
This attaches to the bottom of the camera module to fix the camera module
to a tripod.
6 Camera module interface board
Install the board in a PCI bus slot in devices such as a PC. Select a
commercially available interface board compatible with the Camera Link
feature.
7 1MA26-4560-OSC-200 (2 m, 6.6 ft) / 500 (5 m, 16.4 ft) /
A00 (10 m, 32.8 ft) Camera Link cable
This cable connects to the digital interface connector on the rear panel of
the camera module. Image/control signals are transmitted via this cable.
Select a commercially available cable produced by Sumitomo 3M Limited.
Connection example Fig. C
Connecting DC-700/700CE (not supplied)
Connect the camera module to the power via the camera adaptor DC-700/
700CE.
For details on the camera adaptor DC-700/700CE, see the DC-700/700CE
Instruction Manual.
1 C-mount lens 1 DC IN connector
2 Camera cable (e.g. CCXC-12P05N) 2 To CAMERA connector
3 TRIG generator, Image processor 3 To AC IN connector
4 To AC power source
2
6
1
3 4
3
4
5
4
1
3
2
GND2 GND1
GND1
WEN
TRIG
HD
VD/SYNC
AC IN 1
1
2
2
CAMERA VIDEO
1
2
2
3
1
4
3
DC-700/700CE
XCL-U1000C/U1000
1 2
3 4 5
6 7
Digital Video Camera Module