Samsung CL29K40PQ - Manual (Page 4)

English - 4
◆ Clock
Setting the clock is
necessary in order to use
the various timer features
of the TV. Also, you can
check the time while
watching the TV. (Just
press the INFO button.)
◆ Sleep Timer
You can select a time period of between 30 and
180 minutes after which the TV automatically
switches to standby mode.
➢
Press the SLEEP button on the remote
control repeatedly until the appropriate time
interval appears (any of the preset values
from “30 Min.” to “180 Min.”).
◆ On Timer / Off Timer
You can set the On/Off timers so that the TV will
switch on or off automatically at the time you
select.
➢
You must set the clock first.
◆ On Timer Channel
The preferred channel can be set for when the
timer automatically turns on the TV.
◆ On Timer Volume
The preferred volume can be set for when the
timer automatically turns on the TV.
☛
Auto Power Off
When you set the timer “On”, the TV will
eventually turn off, if no controls are operated for
3 hours after the TV was turned on by timer. This
function is only available in timer “On” mode and
prevents overheating or leakages, which may
occur if a TV is on for too long.
Setup - Time
Move Enter Return
Time
Clock -- : -- am
Sleep Timer : Off √ √
On Timer -- : -- am Off
Off Timer -- : -- am Off
On Timer Channel : 3
On Timer Volume : 10
Channel - Fine Tune
The Fine Tuning function lets
you manually adjust the TV’s
tuner if you have difficulty
tuning channels.
Adjust the fine tuning by
pressing the œ or √ button.
To store the fine tuning setting in the TV’s memory,
press the MENU button.
To reset the fine tuning to “0”, select ”Reset” by
pressing the
▲ or ▼ button, then press the ENTER
button.
Reset
Fine Tune
Move
Adjust Return
3 ✽ 1
Channel - Name
Use this feature to assign an
easy-to-remember label to
any channel (i.e., “CBS”,
“ESPN”, “PBS2”, “CNN1”,
etc.). A label consists of four
fields, where each field is a
letter (A~Z), a number (0~9),
-, or a blank. When the INFO button is pressed, the
channel label will appear next to the channel number.
Move Adjust Return
Name
… … More
2 :
3 : - - - -
4 : - - - -
5 : - - - -
6 : - - - -
† † More
A
Channel - LNA
(depending on the model)
When a weak broadcast
signal causes an unclear,
noisy picture, the “LNA”
feature improves the picture
quality by setting to “On”. If
you experience noise on a
certain channel, set the
“LNA” to “On” or “Off” for this channel, to obtain the
optimum picture.
Move Enter Return
Channel
Air/Cable : Air
Auto Program
Add/Delete
Fine Tune
Name
LNA : Off Off
On
Channel - Memorizing the Channels
Your TV can memorize and store all of the available
channels for both “off-air” (antenna) and cable
channels. After the available channels are memorized,
use the CH
and CH buttons to scan through the
channels.
This eliminates the need to change channels by
entering the channel digits. There are three steps for
memorizing channels: “Air/Cable”, “Auto Program”
and “Add/Delete”.
◆ Air/Cable
Before your TV can begin
memorizing the available
channels, you must
specify the type of signal
source that is connected
to the TV (i.e., an
antenna or a cable
system).
Select “Air” or “Cable” by pressing the … or †
button.
◆ Auto Program
All available channels are
automatically stored in
memory when channels
are selected by the direct
tuning function.
Press the ENTER button
at any time to interrupt
the memorization process.
◆ Add/Delete
You can add or delete a
channel to display the
channels you want only.
To use the Add/Delete
function, first run Auto
Program.
Select “Deleted” or
“Added” by pressing the
… or † button.
Move Enter Return
Channel
Air/Cable :Air
Auto Program
Add/Delete
Fine Tune
Name
LNA
: Off
Air
Cable
Search
Enter Return
Air 3
3%
Stop
Move Enter Return
Add/Delete
… … More
2 : Deleted
3 : Deleted
4 : Deleted
5 : Deleted
6 : Deleted
† † More
Deleted
Added
AA68-03858A-03Eng 8/16/06 1:29 PM Page 4