Preparation for use, Setup, Hint – Sharp DV-NC150U User Manual

Page 12: Yes es, Turn on the unit for the first time, Clock set up, Turn on the tv and set it to channel 3, Please wait for a few minutes. after scanning, Press the menu button to exit

Advertising
background image

Hint

Hint

• To go back one step, press the s button

(during the steps [2] to [7].)

• Your clock setting will be lost if either there

is a power failure or this unit has been
unplugged for more than 30 seconds.

Hint

Hint

• If you accidentally select Spanish or

French and need English: Press the
MENU button and choose SELEC.
IDIOMA, or SELECTION LANGUE. Press
the B button, and select ENGLISH. Finally,
press the CLEAR/C.RESET button.

– 12 –

EN

Setup

2

2

LANGUAGE SELECT

B ENGLISH

[ON]

FRANCAIS

ESPAÑOL

Hint

Hint

• Repeat these steps only if either there

was a power failure or this unit has been
unplugged for more than 30 seconds.

1

1

Turn on the TV and set it
to channel 3.

• If channel 3 is already occupied for broadcasting,

see“RF Output Channel” section.

POWER

3

3

CH 01

AUTO SET UP

To Preset the Channel Again

1) Press the MENU button until the main

menu appears.

2) Select "CHANNEL SET UP" by pressing

the K or L button. Then, press the B but-
ton.

3) Select "AUTO SET UP" by pressing the

K or L button. Then, press the B button.
After scanning, the tuner stops on the low-
est memorized channel.

To Change the On-Screen Language

1) Press the MENU button until the main

menu appears.

2) Select "LANGUAGE SELECT" by press-

ing the K or L button. Then, press the B
button.

3) Select "ENGLISH" , "FRANCAIS" or

"ESPAÑOL" by pressing the K or L but-
ton. Then, press the CLEAR/C.RESET
button.

No

No

Please wait for a few minutes.

After scanning...

• The tuner stops on the lowest memorized

channel.

• You can select only the channels memo-

rized in this unit by using the SKIP/CH.
(

K/L) buttons.

• If "AUTO SET UP" appears on the TV

screen again, check the cable connections.
Then, press the B button once again.

Y

Y

es

es

Press the MENU
button to exit

• Refer to “Hint for Cable Box

or Satellite Box” section on
page 8.

Do you connect the cable from the cable box or
the satellite box to the VCR/DVD’s ANT IN jack?

YES

NO

Turn on the unit for the first
time

TV Screen

Remote Control

Clock Set Up

To Select a Channel

You can select a channel by directly
entering channel using the Number but-
tons on the remote control.
Notes for using the Number buttons:
• When selecting cable channels which

are higher than 99, enter channel
numbers as a three-digit number.(For
example: 117, press 1,1,7)

• You must precede single-digit channel

numbers with a zero (For example:
02, 03, 04 and so on).

VCR

VCR

Preparation for Use

5

5

4

4

CLOCK SET

MONTH DAY

YEAR

0 3 / 1 5

2 0 0 4

HOUR MINUTE

AM/PM

– – : – –

– –

CLOCK SET

MONTH DAY

YEAR

0 3 / 1 5 MON 2 0 0 4

HOUR MINUTE

AM/PM

0 5 : – –

– –

6

6

CLOCK SET

MONTH DAY

YEAR

0 3 / 1 5 MON 2 0 0 4

HOUR MINUTE

AM/PM

0 5 : 4 0

– –

7

7

CLOCK SET

MONTH DAY

YEAR

0 3 / 1 5 MON 2 0 0 4

HOUR MINUTE

AM/PM

0 5 : 4 0

P M AM

B PM

Select the current year

Select “AM” or “PM”

8

8

To exit the CLOCK SET
screen.

Select the current hour

Select the current minute

or

or

or

or

or

VCR

1

1

-MENU-

TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP

B CLOCK SET

LANGUAGE SELECT
AUDIO OUT
TV STEREO

[ON]

SAP

MENU

2

2

CLOCK SET

MONTH DAY

YEAR

0 3 / – –

– – – –

HOUR MINUTE

AM/PM

– – : – –

– –

3

3

CLOCK SET

MONTH DAY

YEAR

0 3 / 1 5

– – – –

HOUR MINUTE

AM/PM

– – : – –

– –

Select the current month

Select the current day

• If the clock is not set, the

CLOCK SET screen
appears when you press
the MENU button. In this
case, go to step [2].

VCR

VCR

or

or

or

VCR

Advertising