Samsung ML-1630W Series - Manual (Page 22)

3 .3
<Getting Started>
2 Temporarily disable the computer firewall before continuing by doing
the following:
3 From the Windows Start menu, select All Programs > Samsung
Network Printer Utilities
> SetIP > SetIP.
4 Click on the icon(third from left) in the SetIP window to open
the TCP/IP configuration window.
5 Enter the machine’s new information into the configuration window
as follows:
• MAC Address: Find the machine’s MAC address from the Network
Configuration Report and enter it without the colons.
For example, 00:15:99:29:51:A8 becomes 0015992951A8.
Note
MAC address is a hardware serial number of the machine’s
network interface and can be found in on the Network
Configuration Report
.
• IP Address: Enter a new IP address for your printer the same as the
computer’s IP address except for the last number.
For example, if your computer’s IP address is 192.168.1.150, enter
192.168.1.X. (X is number between 1 and 254 other than the
computer’s address.)
• Subnet Mask: Enter this exactly the same as the computer’s Subnet
Mask.
• Default Gateway: Enter this exactly the same as the computer’s
Default Gateway.
6 Click Apply, and then click OK. The machine will automatically print
the Configuration report. Confirm that all the settings are correct.
7 Click Exit to close the SetIP program.
8 If necessary, restart the computer’s firewall.
Window XP
• Open Control Panel.
• Double click Security
Center .
• Click Windows Firewall.
• Disable the firewall.
Macintosh OS
• Open System Preferences.
• Click Sharing.
• Click the Firewall menu.
• Turn firewall off.
Network parameter setting
You can also set up the various network settings through the network
administration programs.
• SyncThru™ Web Admin Service: Web-based printer management
solution for network administrators. SyncThru™ Web Admin Service
provides you with an efficient way of managing network devices and
lets you remotely monitor and troubleshoot network machines from
any site with corporate internet access. Download this program from
http://solution.samsungprinter.com .
• SyncThru™ Web Service: Web server embedded on your network
print server, which allows you to: (A) Configure the network
parameters necessary for the machine to connect to various network
environments. (B) Customize machine settings.
Installing the software
You must install the printer driver software for printing. The software
includes drivers, applications, and other user friendly programs.
Make sure that the network setup for your machine is completed. (See
"Setting up the network" on page 3.2.) All applications should be closed
on your computer before beginning the installation.
If your IP assignment method is DHCP and IP address can be changed
whenever machine in turned on, we recommend you to use the Bonjour
program. Go to the http://developer.apple.com/networking/bonjour/
download/ , select the program Bonjour for Windows according to your
computer operating system, and install the program. In case of Mac OS
X, this program might be already installed in your PC. This program will
allow you to fix the network parameter automatically. This Bonjour
program does not support Linux.
If your IP assignment method is static, follow the steps below.
1 Insert the Printer Software CD-ROM into your CD-ROM drive. The
CD-ROM should automatically run, and an installation window
appears.
2 Click Next.
If the installation window does not appear, click Start > Run. Type
X:\Setup.exe, replacing “X” with the letter which represents your
drive and click OK.
If you use Windows Vista, Windows 7 and Windows Server 2008
R2, click Start > All Programs > Accessories > Run, and type
X:\Setup.exe.
Note
The installation window may slightly differ, if you are
reinstalling the driver.
3 Select Typical installation for a network printer, and then click
Next
.
Note
The following procedure is based on Windows XP. The procedure
and popup window which appears during the installation may
differ depending on the operating system, machine features, or
the interface in use.