Samsung DVD-V2500 - Manual (Page 7)

Basic Connections/Auto Setup
13
Using the TV Buttons on the Remote Control
12
In this section, you will connect the DVD-VCR to your television
and run Auto Setup, which automatically searches for channels and
sets the player’s internal clock.
NOTES:
• See Appendix A for Advanced Connections.
• Standard RF or Line connection between DVD-V2500 & your TV
are required to run DVD+VCR setup menu, even if
you connect S-Video or Component Video Output
for a better picture quality.
1 Connect Antenna/Cable to DVD+VCR
Connect an external indoor/outdoor antenna or wall outlet antenna
cable to the Ant-In jack on the rear panel of DVD-V2500.
2 Connect DVD+VCR to TV
Choose one of the following methods to connect the DVD-VCR to your TV:
RF Connection
Connect the supplied RF antenna cable from the OUT (TO TV) jack
on the back panel of the DVD-VCR to your television’s Antenna Input.
Line Connection
Connect an RCA-type audio/video cable (red, white, yellow) from
the LINE OUTjacks on the back panel of the DVD–VCR to your
television’s Line In jacks. Use red for right audio, white for left
audio, and yellow for video.
NOTE: It is recommended that you use the Line Connection if your
TV is equipped with RCA jacks.
3 Plug In
Connect the DVD-VCR power cord to a standard 120V/60Hz wall
outlet. Don’t press any buttons on the DVD-VCR or remote during
auto setup. “AUTO” blinks while the DVD-VCR runs an auto setup
procedure, where it will automatically search for all active channels
and set the clock. When Auto setting has been completed, the front
panel displays the current time. If Auto Clock set is unable to find a
channel to set the clock, you can set the clock manually; See page
18.
4 Turn On DVD+VCR
Press the POWER button on the remote control or on the
DVD–VCR’s front panel.
5 Turn On TV
Press the POWER button on your TV.
6 Set TV to Channel 3, 4 or Line
Be sure to use the same channel you selected in Step 2. If you
used the Line Connection, set your TV to its Line Input.
From Antenna or Cable
To TV’s Antenna Input
1
2
2
3
4
4
Your VCR remote control will work with Samsung televisions and
compatible brands.
To determine whether your television is compatible, follow the instructions
below.
1 Switch your television on.
2 Point the remote control towards the television.
3 Hold down the TV button and enter the two-figure code
corresponding to the brand of your television, by pressing the
appropriate numeric buttons.
Brand Codes Brand Codes
SAMSUNG 01, 14, 15, 23 LOEWE 28
SHARP 02, 16, 22 ZENITH 17
SONY 03 LG 06, 08, 18
RCA 07, 29 MAGNAVOX 04
TOSHIBA 09 EMERSON 21
PANASONIC 12, 24 SANYO 05, 20
JVC 11 DAEWOO 19
HITACHI 10 NOBLEX 25
MITSUBISHI 13 TELEFUNKEN 26
NEWSAN 27
Result: If your television is compatible with the remote control, it
will switch off. It is now programmed to operate with the
remote control.
➢
If several codes are indicated for your television brand, try
each one in turn until you find one that works.
☛
When you change the batteries in the remote control, you
must reprogram the code, following the same procedure.
You can then control the television using the following buttons.
Button Function
POWER ➀ Used to switch the television on and off.
INPUT SEL. ➁ Used to select an external source.
VOL + or – ➂ Used to adjust the volume of the television.
CH ( or ) ➃ Used to select the required channel.
MUTE ➄ Used to toggle the sound on and off.
➢
The various functions will not necessarily work on all
televisions. If you encounter problems, operate the
television directly.
1
2
3
3
4
4
5
00006A DVD-V2500/XAC-Eng1 11/12/02 7:03 PM Page 12