Sharp FO-475TH User Manual

Page 23

Advertising
background image

UX-258TH
FO-475TH

SW-D1 No. 1 ~ No. 4 Number of rings for auto receive

When the machine is set in the auto receive mode, the number of rings
before answering can be selected. It may be set from one to nine rings
using a binary number. Since the facsimile telephone could be used as
an ordinary telephone if the handset is taken off the hook, it should be
programmed to the user’s choice. If the soft switch was set to 1, direct
connection is made to the facsimile. If a facsimile calling beep was heard
when the handset is taken off the hook, press the START key and put
the handset on the hook to have the facsimile start receiving. If it was
set to 0 accidentally, receive ring is set to 1.
NOTE: If the machine is set to answer after a large number of rings, it

may not be able to receive faxes successfully. If you have diffi-
culty receiving faxes, reduce the number of rings to a maximum
of 5.

SW-D1 No. 5 Automatic switching manual to auto receive mode

This soft switch is used to select whether the machine should switch to
the auto receive mode after 5 rings in the manual receive mode or re-
main in the same way as SW-D1 No. 1, No. 2, No. 3 and No. 4 "0"1"0"1"(5
rings).

SW-D1 No. 6 ~ No. 8 Reserved

Set to "0".

SW-D2 No. 1 ~ No. 5 Reserved

Set to "0".

SW-D2 No. 6, No. 7 CI off detection timer (Distinctive ring setting
off only)

Set the minimum time period of CI signal interruption which affords to be
judged as a CI OFF section.

SW-D2 No. 8 Reserved

Set to "0".

SW-E1 No. 1 Tel/Fax Automatic switching mode

Used to set auto TEL/FAX switching mode or to set the normal fax mode.

SW-E1 No. 2, No. 3 Pseudo ringing time at the phone/fax automatic
switching mode

Choice is made as to how long to rumble the dummy ringer on TEL/FAX
automatic switching mode.

SW-E1 No. 4 Number of CNG signal detection at the phone/fax
automatic switching mode

Used for detection of CNG in one tone or two tones in the TEL/FAX
automatic switching mode.

SW-E1 No. 5 CNG detect time at TEL/FAX mode

The switch which sets the time from the start of CNG detection to the
end of detection.

SW-E1 No. 6 ~ No. 8 Reserved

Set to "0".

SW-E2 No. 1 ~ No. 4 Pseudo ringer sound output level to the line

Used to adjust sound volume of pseudo ringer to the line (ring back
tone) generated on selecting TEL/FAX. Setting is the reduce level from
-5 dBm output level.

SW-E2 No. 5 ~ No. 8 Reserved

Set to "0".

SW-F1 No. 1, No. 2 DTMF detect time

Used to set detect time of DTMF (Dual Tone Multi Frequency) used in
remote reception (5 ).

The longer the detect time is, the less the error detection is caused by
noises.

SW-F1 No. 3 Protection of remote reception (5 ) detect

Used to set the function of remote reception (5 ). When set to "1",
the remote reception function is disabled.

SW-F1 No. 4 Remote reception with GE telephone

(Corresponding to TEL made by GE) P. B. X.

"1": Compatible with TEL mode by GE

"0": Not compatible

When sending (5 ) for remote reception with a GE manufac-

tured telephone remote reception may not take place because of
special specifications in their DTMF.

To overcome this, a soft SW is provided to change the modem set-

ting to allow for remote reception.

If this soft SW is set to "1", other telephone sets may be adversely

affected.

SW-F1 No. 5 ~ No. 8 Remote operation code figures by external
TEL (0 ~ 9)

Remote operation codes can be changes from 0 through 9. If set to
greater than 9, it defaults to 9. The "5 " is not changed.
Ex-7 (Default: 5 )

SW-F2 No. 1 CNG detection in STAND-BY mode

When setting to "1", the CNG signal detection function during standby
stops.

SW-F2 No. 2, No. 3 Number of CNG detect (AM mode)

Used for detection of CNG in 1 to 4 pulses.

SW-F2 No. 4, No. 5 Number of CNG (STAND-BY mode)

Used for detection of CNG in 1 to 4 pulses.

SW-F2 No. 6 Fax signal detection after telephone mode dial

When set to "1", if machine detect the fax answering signal after tel-
ephone calling (handset off-hook or speaker mode dial), machine start
to receive the documents automatically.

SW-F2 No. 7, No. 8 Reserved

Set to "0".

SW-G1 No. 1 ~ No. 8 Reserved

Set to "0".

SW-G2 No. 1 ~ No. 8 Reserved

Set to "0".

SW-G3 No. 1 ~ No. 8 Reserved

Set to "0".

SW-H1 No. 1 Busy tone detection ON/OFF time (Lower duration)

The initial value of detection is set according to electric condition.

The set value is changed according to the local switch board. (Erro-
neous detection of sound is reduced.)

Normally the upper limit is set to 900msec, and the lower limit to 150msec.

If erroneous detection is caused by sound, etc., adjust the detection
range.

The lower limit can be set in the range of 350msec to 150msec.

SW-H1 No. 2 Busy tone detection ON/OFF time (Upper duration)

Similarly to SW-H1 No. 1, the set value can be varied.

The upper limit can be set in the range of 650msec to 900msec.

2 – 14

SW-H1 No. 1

SW-H1 No. 2

Detection range

0

0

150msec ~ 900msec

0

1

150msec ~ 650msec

1

0

350msec ~ 900msec

1

1

350msec ~ 650msec

A

B

400msec

2000msec

1

2

Advertising
This manual is related to the following products: