Skylink 838A User Manual

Fcc information, Receiver installation, Transmitter installation

Advertising
background image

re

g

is

te

re

d

t

ra

d

e

m

a

rk

o

f

s

k

y

lin

k

T

e

c

h

n

o

lo

g

ie

s

I

n

c

.,

R

The code Scrambler
Anti-Theft Garage Door
Remote Control
Operating Instructions
( Model 838A )

PROGRAMMING THE NEW TRANSMITTER & RECEIVER

(1) Each transmitter was assigned an
individual (never duplicated) code in the
factory. For the receiver to recognize and
respond to the transmitter, it must first
“learn” the code. With the receiver
installed in the operator, remove the front
lower cover of the receiver case, press
and hold Button 1 on the receiver, (its red
light will flash), while simultaneously
pressing and holding Button A on the
transmitter, until the receiver light stops
flashing indicating it has learned the
code.

(2) Test the new transmitter. If it does not
operate your garage door, repeat Step 1.

FCC INFORMATION

The Code Scrambler Anti-Theft Garage
Door Remote Control uses an FCC approved
transmitter and receiver, and complies with
part 15 of the FCC Rules. Its operation is
subject to the following two conditions:
1. This device may not cause harmful
interference.
2. This device must accept any interference
that may be received, including
interference that may cause undesired
operation.

TM

Warning : Changes or modifications to this
unit not expressly approved by
the party responsible of
compliance could void the user’s
authority to operate the
equipment.

(3) To program Button B to operate another
garage door, repeat Steps 1 & 2 with a
second receiver (sold separately).

(4) If you use the transmitter to operate only
one door, with either Button A or B,
repeat Steps 1 & 2, using Button B.

CAUTION : if you press and hold the
button 1 and button 2 on the receiver and
then release the Button 2 (its red light will
flash faster), this will erase all of the
“ learned ” codes in its memory. Repeat
the “ learning ” process with each
transmitter.

Skylink will not be liable or responsible for
any misuse or application of this product
other than for its intended use.

CUSTOMER SERVICE
17 Sheard Avenue, Brampton,
Ontario, Canada L6Y 1J3
Email: [email protected]
Customer Service : (800) 304-1187
From 9am to 5pm EST (Mon-Fri)
http://www.skylinkhome.com
P/N.101A366
Patent no. D382251, D380895
2005 SKYLINK GROUP

C

RECEIVER INSTALLATION

(1) Your receiver is an universal radio digital
receiver:
Operating voltage is from 18V to 30V
AC or DC supplied by the garage or
gate operator.

(2) Wiring connection:
White wire - connect to common.
Red wire - connect to 24V
Black Wire - relay output, connect to relay

(3) Antenna wire:
Please DO NOT remove the yellow wire,
ensure that it is in up-right position to
receive data signals from the transmitter.

TRANSMITTER INSTALLATION

(1) Operating source :
Operated by 12 Volt “ cigarette lighter ”
type (size 23A) Alkaline battery
(included)

(2) Battery replacement :
Remove the battery cover, then install a
new battery when LED dim. Then
replace the battery cover after the
installation.

Button B

Button A

BUTTON 1

Red Light

BUTTON 2

WARRANTY

If, within one year from date of purchase,
this product should become defective
(except battery), due to faulty workmanship
or materials, it will be repaired or replaced,
without charge, Proof of purchase is
required.

Warning ! Do not let children use the
garage door transmitter without adult
supervision. Children can injure
themselves or others the garage door.

RED

BLACK

WHITE

BATTERY

Advertising
Table of contents