Rear panel jacks, Chapter one connecting the set top box – Samsung SIR-T351 User Manual

Page 11

Advertising
background image

ΠAIR/CATV INPUT (75

)

Connect the AIR antenna or CATV antenna here. Connect
cable in the event that a local cable provider is passing
through 8VSB and Clear QAM on their system.

´ VIDEO OUT

If your TV or monitor has Audio/Video capability, connect
this jack to the AV Input jack on your TV or monitor using
an Audio/Video cable.
Use this output for conventional TV sets that do not have
S-Video or component video inputs.

ˇ S-VIDEO OUTPUT

Provides good picture quality. If your TV or monitor has
S-Video capability, use this jack along with the
Audio/Video jacks to connect the Set-Top Box.
Use this output for conventional TV sets that have an S-
Video input but no component video inputs.

¨ DTV OUT COMPONENT (Y, P

B

, P

R

format)

You can connect Y-P

B

-P

R

to a TV, computer monitor, or

another video component input. As with DTV OUT (Y-P

B

-P

R

format), 1080i, 720p, and 480p are available by setting
the RESOLUTION SELECT switch.

ˆ Lt/Rt ANALOG-AUDIO OUTPUTS

Connect these terminals to the analog audio inputs of a
TV set (i.e., to a TV that has jacks for L/R inputs).
Or, connect these terminals to the L/R inputs of a sepa-
rate audio component.

Ø DOLBY DIGITAL OUTPUT (COAXIAL)

Use to connect the Digital Audio Input of your TV.

DTV OUT (RGB format)

You can connect RGB to a TV, computer monitor, or
another video component input. 1080i, 720p, 480p and
480i are available by setting the RESOLUTION SELECT
switch.

DOLBY DIGITAL OUT (OPTICAL)

Use to connect the Digital Audio Input of your TV or
audio component.

Service Jack

For service only.

˝ DTV OUT SELECT

Use to select YP

B

P

R

/RGB,DVI according to the video

output from the TV or monitor.

Ô RESOLUTION SELECT

Switches between 1080i (interlaced scanning), 720p
(progressive scanning), 480p (progressive scanning), and
480i (interlaced scanning) formats.
Switches the DTV Component outputs to the following for-
mats:
• 1080i (Interlaced Scanning)

Use this setting for an HDTV Ready 16 X 9
(WIDESCREEN) aspect ratio TV monitor that can handle
the 1080i video output format.

• 720p (Progressive Scanning)

Use this setting for an HDTV Ready 16 X 9
(WIDESCREEN) aspect ratio TV monitor that can handle
the 720p video output format.

• 480p (Progressive Scanning)

Use this setting for an Digital Ready 4 X 3 aspect ratio
TV monitor with Progressive Scan DTV ready compo-
nent video inputs that can handle the 480p video out-
put format.
The TV monitor may be labeled Enhanced Definition or
Progressive Scan, but not Wide Screen.

• 480i (Interlaced Scanning).

Use this setting for a conventional TV with regular
video, S-Video, or component video inputs.

DVI OUT

Use to connect a device equipped with DVI interface. DVI
OUT supports HDCP function. (See Notes on page 16.)

NOTE

The use of 1080i on a 4 X 3 monitor or the use of 480p on a

16 X 9 monitor may cause Aspect Ratio picture distortion.
720p will only work on selected HDTV Ready TVs. Check the TV
monitor's owner's manual to verify this capability. 480i will
only work on conventional TV sets.

CHAPTER ONE
Connecting The Set Top Box

1

1

11

Rear Panel Jacks

MD68-00XXXA(E)-CHAPTER 1 4/4/03 10:56 AM Page 11

Advertising