Sierra Products EF-5001UB - Manual

Sierra Products, Inc.
506 1 Brook s St., S te. B
Montclair, CA 91763
Listed by OMNI-Test Laboratories, Inc.
Rep ort No . 256-S-01-4
Please read this entire manual before installation. Save these instructions.
EF5001U-B Pellet Heater
Installation & Operating Instructions
SAFETY NOTICE
< CAUTION: HOT W HILE IN OPERATION. KEEP
CHILDREN, CLOTHING AND FURNITURE AWAY.
CONT ACT MAY CAUSE SKIN BURNS.
< IF THIS HEATER IS NOT PROPERLY INSTALLED,
A HOUSE FIRE MAY RESULT.
< FAILU RE TO CO M PLY W ITH OW NE RS ' MANU AL
INSTRUCTIONS WILL VOID YOUR WARRANTY!
WARNING: THIS HEATER SHOULD NOT BE
INSTALLED IN A SLEEPING ROOM.
PLEASE READ THIS ENTIRE MANUAL BEFORE
INSTALLATION AND USE OF THIS PELLET FUEL-
BURNING ROOM HEATER. FAILURE TO FOLLOW
TH ES E IN ST RU CT ION S C OU LD RE SU LT IN
PROPERT Y DAMAGE, BODILY INJURY OR EVEN
INSTALLER: PLEASE LEAVE THIS MANUAL WITH
THE OWNER!!
GENERAL INFORMATION
Installation and repair should be done by a qualified service
person. The heater should be inspected before use and at
least annually by a professional service pers on. More
fre qu en t cle an ing m ay be re qu ired due to fue l quality,
ex ce ss ive lint fr om carpetin g, b ed ding m ate rial, etc . It is
im pera tive that con trol com partm ents , burn ers and circu lat-
ing air passageways of the heater be kept clean.
The EASYFIRE Pellet heater has been designed and
approved for burning w oo d p ellet fu el on ly. Burning other
forms of fuel is not permitted and will void all warranties.
This unit has been approved for use with a 4" Type L Pellet
Vent System .
NEVER use gasoline, gasoline-type lantern fuels, kerosene,
charcoal lighter fluid, or similar liquids to start or "freshen
up" a fire. Keep all such liquids well away from the heater
while it is in use.
Ashes must be disposed of in a metal container with a tight
fitting lid and placed on a noncombustible floor or ground,
we ll away fr om all fu els , pe nd ing fina l dispo sa l.
NOTE : During the first few burns the high tem perature
paint and sealant used in manufacture will emit some odor
and smoke. Open doors and windows to the outside for
proper ventilation during the first burn cycle and curing of
the p aint.
This heate r, whe n insta lled, m us t be electrica lly gro un de d in
accordance with local codes or, in the absence of local
codes, with the National Electrical Code, ANSI/NFPA 70-
2006.
Provide adequate clearances around air openings into the
combustion chamber and adequate accessibility clearance
for servicing and proper operation. Never obstruct the front
opening of the hea ter.
The heater may be installed as a free-standing unit mounted
on a non -com bu stib le protec tive floo r pa d or he arth. O r it
m ay be m ounted into an existing U. L. approved w ood stove
chimney. Non-combustible floor protection is required and
m us t be used wh en placin g th e hea ter on any com bu stib le
m ate rial.
The pellet heater must be operated with a power source and
will not operate using natural draft. If there is a powe r failure
the heater will shut down. If the 12 volt back system is in-
stalled, the heater will automatically switch to 12 volt power.
The EasyFire Pellet Heater has been listed by OM NI-Test
Laboratories, Inc. to ASTM, U.L.,and EPA Standards.