Skylink PS-201 - Manual

2. INSTALLATION
1. INTRODUCTION
Motion Sensor
Model PS-201
The Motion Sensor is designed to activate the Skylink’s swing door
opener automatically when it senses motion nearby the door. The door
will stay open for a period of time then closes if no further movement is
detected.
In this package, you should find a Motion Sensor
(battery included), ball-head joint and screws.
Please follow the instructions below to setup your motion sensor.
2 pcs 3 x 18 screws
(Included)
Motion Sensor Ball-head joint
2. INSTALLATION (CONT)
9V Alkaline
battery
Insert a 9V alkaline battery
(included) to the motion
sensor and its LED will
be on for 2 seconds.
Before installing the sensor onto the wall or door frame, you should “learn”
the sensor to the door opener so they can communicate.
To “learn” the motion sensor to the door opener, follow the procedures
below:
1. The door opener should be in standby mode, i.e. adapter plugged in
but the swing door opener should not be operating, only the red LED
should be on steadily.
2. Press and hold the “Learn” button, the red LED will start to flash and
buzzer will beep indicating the door opener is now in learn mode.
3. Press the test button on the motion sensor while you are holding onto
the learn button on the door opener, you should hear a long beep and
the LED will be off. You may now release both the learn button on the
door opener and the test button on the sensor. You have now
successfully programmed the motion sensor to the door opener.
Note: During the installation of the motion sensor, it is recommended to
disable the power supply to the door opener so the door will not open or
close during the installation.
Test
Button
LED
on
9V
Alkaline
Battery
The motion sensor should be installed
above the door as illustrated. You can
mount the ball joint on the wall by
screws.
Once the ball-head joint is mounted
to the wall, slide the back of the
sensor into the ball-head joint (see
diagram). The mounting angle can
be adjusted. Please refer to “Walk
Test” to determine the best
mounting angle.
Walk Test
After mounting the motion sensor, it is important to test the coverage of
the motion sensor. In order to control how far the sensor can “see”, this
can be done by adjusting the angle. You should adjust the angle so it only
monitors several feet away from the door to prevent false trigger by
motion from a far distance.
You should walk in the area that you would
like the sensor to monitor. If movement is detected the red light inside the
unit will appear. If the red light does not appear, adjust the mounting angle
accordingly. Perform the walk test again after 3 seconds. Repeat this
procedure until your motion is detected. There should be no movement in
the detected area during the 3 seconds.
Perform walk test in the undesired
area to ensure movement cannot
be detected.
Tips: The sensor should not face towards direct
sunlight, placing near heat or cold producing devices
(i.e. A/C or furnance vents, fans, ovens, heaters etc.)
that may cause false triggers.
When the motion sensor is triggered, the door opener will open the door.
In order to close the door automatically, the door opener must be set in the
“Timer” operating mode.
3. OPERATION
Move the sensor
downward to reduce
the range.
You may change the timer setting from 10 seconds to 50 seconds, in 10-
second intervals.
To change the timer setting:
1. Press and hold the door setting button for 3 seconds when the door
opener is in standby mode. You will hear the buzzer beeping rapidly
and the orange LED flashing. You may now release the door setting
button.
2. After the door setting button is released, you should hear the buzzer
beeping. This buzzer beeping represents the timer setting.
1
Timer Setting
10 Seconds
2
3
4
5
20 Seconds
50 Seconds
Number of continuous beep
To enable the timer mode:
1. Unplug the door opener when it is in standby mode.
2. Change the setting of the mode selection switch to “Timer” mode
(top position).
3. Plug the adapter back and the red LED will be on steadily.
4. Open the door by activating the remote or walking in front of the
motion sensor. After the door has been opened, you should still
hear the buzzer beeping, indicating that the timer is counting down
and the door will be closed soon. The factory default timer is set to
10 seconds.
5. After 10 seconds, the door will be closed automatically.
Top position -
"Timer mode". Learn button
30 Seconds
40 Seconds