Sony SPP-N1004 - Manual (Page 4)

Resetting the digital security code
The first time you charge the battery pack, a random security code is automatically
assigned between the base unit and the handset. Only a handset which has this
security code can make calls through the base unit. This system prevents the
possibility of other cordless telephone handsets making calls through your base unit.
You normally do not need to reset the security code. However, in the unlikely event
that you suspect that another cordless phone uses the same security code, you can
manually change the code. Pick up the handset from the base unit, and proceed as
follows:
Note
If the battery pack in the handset is completely discharged, or is removed from the handset for
more than several seconds, the digital security code stored will be lost. If this happens, charge the
battery pack and a new security code will be automatically assigned.
Tip
This procedure will change the code in both the base unit and the handset. The code can be
changed as often as desired.
Mounting the base unit on a wall
1
Attach the telephone line cord and AC power adaptor cord to the base
unit. Bundle the loose telephone line cord or AC power adaptor cord, if
necessary.
2
Plug the telephone line cord into the telephone outlet, and hook the base
unit to the wall plate as illustrated. Plug the AC power adaptor to an AC
outlet. Then raise the antenna so that it points towards the ceiling.
Maintenance
• Clean the cabinets with a soft cloth slightly moistened with water or a mild
detergent solution. Do not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine as they may damage the finish of the cabinet.
• If the charge terminals of the base unit and handset are soiled, wipe them with a
soft cloth.
If you have any questions or problems concerning your phone, please consult your
nearest Sony dealer.
Notes on power sources
On battery pack
• Store the battery pack at a temperature between 41°F (5°C) and 95°F (35°C) for
best performance.
• If you do not use the cordless handset for a long period of time, remove the battery
pack.
On power failure
• During a power interruption, you cannot make or receive calls.
For the customers in the USA
RECYCLING NICKEL-CADMIUM BATTERIES
Nickel-Cadmium batteries are recyclable. You can help preserve our
environment by returning your unwanted batteries to your nearest
point for collection, recycling or proper disposal.
Note: In some areas the disposal of nickel-cadmium batteries in
household or business trash may be prohibited.
RBRC (Rechargeable Battery Recycling Corporation) advises you
about spent battery collection by the following phone number.
Call toll free number: 1-800-822-8837 (United States and
Canada only)
Caution: Do not handle damaged or leaking nickel-cadmium batteries.
Troubleshooting
Should any problem persist after you have made these checks, consult your nearest
authorized Sony dealer.
Specifications
General
Operating frequency 902-928 MHz bands
Frequency control Crystal-controlled PLL
Operation mode FM, duplex
Operation channel 30 channels
Supplied accessories AC power adaptor AC-T127
Telephone line cord
Rechargeable battery pack BP-T50
Handset
Power source Rechargeable battery pack BP-T50
Battery life Standby: Approx. 30 days
Talk: Approx. 10 hours
Dimensions Approx. 2 1 / 4 Ч 7 1 / 8 Ч 1 15 / 16 inches (w/h/d), antenna excluded
(approx. 55 Ч 180 Ч 48 mm)
Antenna: Approx. 1
15 / 16 inches (approx. 48 mm)
Mass Approx. 5.5 oz (approx. 155 g), battery included
Base unit
Power source DC 9V from AC power adaptor
Battery charging time Approx. 12 hours
Dimensions Approx. 4 1 / 4 Ч 2 1 / 8 Ч 8 3 / 8 inches (w/h/d), antenna excluded
(approx. 107 Ч 52 Ч 212 mm)
Antenna: Approx. 4
5 / 8 inches (approx. 115 mm)
Mass Approx. 7.6 oz (approx. 215 g)
Design and specifications are subject to change without notice.rencia rápida
1
Press (PGM).
The TALK/BATT LOW lamp
flashes.
2
Press (#).
You hear a confirmation beep.
3
Press three of the dialing keys
(001 to 999) to store a new code.
4
Press (PGM).
You hear a long confirmation
beep and the TALK/BATT LOW
lamp goes off.
5
Immediately replace the handset
on the base unit.
You hear a long confirmation
beep and the phone stores the
new code.
1, 4
2
TALK/BATT
LOW lamp
1 2
AC power
adaptor cord
Telephone
line cord
Bundle the loose
telephone line cord
or AC power
adaptor cord, if
necessary.
Wall plate
AC power
adaptor
AC outlet
Symptom Remedy
The handset does not make
or receive a call. • Reset the digital security code.
• Place the base unit away from noise sources such as TV,
FM radio or PC.
• Make sure the base unit is connected to an AC outlet.
• The battery pack may be discharged. Charge the battery
pack for more than 12 hours.
You hear no dial tone. • Make sure the telephone line cord is securely connected
to the telephone outlet.
The handset does not
connect at all, even the
numbers you dial are
correct. • Choose an appropriate dialing mode again.
The handset does not redial
correctly. • Make sure the number (including the tone and pause
digits, if used) you last dialed is less than 32 digits.
The handset does not make a
speed dialing call. • Make sure there is a phone number correctly stored in
the speed dialing.
• Store the desired phone number once more.
The handset does not ring. • Make sure the base unit is connected to an AC outlet.
The handset does not ring
when paging from the base
unit. • The battery may have little or no power. Charge the
battery pack for more than 12 hours.
• Place the base unit away from noise sources.
You hear a beep every three
seconds and the TALK/
BATT LOW lamp flashes. • Charge the battery pack for more than 12 hours.
The handset does not work. • The battery pack may be discharged. Charge the battery
pack for more than one minute. After this initial one
minute, you may be able to use the handset, but more
than 12 hours are necessary for full charging.