Samsung sv 255B - Manual (Page 15)

GB
27
Using the G-CODE Feature ★(SV-655B/655X/255B Only)
SPEED DUB TV/VCR TIMER
1
G-CODE
CODE ---------
CODE: 0-9 CORRECT: ➛
END: MENU
** TIMER METHOD **
STANDARD
G-CODE
➐❷ ❿ END: MENU
Before presetting your VCR:
◆ Switch on both the television and your VCR
◆ Check that the date and time are correct
◆ Insert the cassette on which the programme is to be
recorded (safety tab intact)
Up to six programmes can be preset.
1 Press the TIMER button.
Result:
The TIMER METHOD is displayed.
2 Press the corresponding ➐ or ❷ buttons, until the G-CODE option
is selected.
3 Press the ❿☎ button to select G-CODE .
Result: A message is displayed to allow you to enter the
G-CODE code.
☛
If all six programmes have been set, the message TIMER
IS FULL is displayed. Refer to page 29 if you wish to
cancel a preset recording.
4 Press the numeric buttons to enter the code opposite the pro-
gramme that you wish to record in your television magazine.
➢
If you wish to correct the G-CODE code that you are
entering:
◆ Press the ➛ button until the digit to be corrected is
cleared
◆ Enter the correct digit
5 Press the MENU button.
Result:
The information concerning the programme is displayed.
☛
When using the G-CODE function for the first time with
stored stations, the programme number flashes. This one
time, you must enter the station number manually by
pressing the
➐ or ❷ buttons. Refer to the following page if:
◆ The programme number or times flash
◆ You wish to modify the programme
6 If the programme and times are correct, press the MENU button.
7 Press the VCR STANDBY/ON (STANDBY/ON) button to activate
the timer.
Result:
The Timer indicator ( ) is displayed.
☛
If no cassette has been inserted when you press
VCR STANDBY/ON (STANDBY/ON) the Timer indicator
flashes. If the safety tab on the cassette has been broken,
the cassette is ejected. Insert the appropriate cassette.
8 Refer to page 29 if you wish to:
◆ Check that your VCR has been programmed correctly
◆ Cancel a preset recording
☛
The numbers next to each TV programme listing are
G-CODE code numbers, which allow you to programme
your videorecorder instantly with the remote control. Tap
in the G-CODE code for the programme you wish to
record.
™ G-CODE is a trademark of Gemstar Development Corporation. The G-CODE system is
manufactured under licence from Gemstar Development Corporation.
V IPC +
NICAM
PROG 1/JAN MON 21:28
PR DAY START → STOP
L1 MO 1 12:00 → 12:50SP
-- ---- --:-- → --:----
-- ---- --:-- → --:----
-- ---- --:-- → --:----
-- ---- --:-- → --:----
-- ---- --:-- → --:----
➐❷ ➛❿
DELETE: CLR/RST MENU
26
Modifying G-CODE Programming ★(SV-655B/655X/
SV-255B Only)
If you wish to correct the programme displayed or modify certain elements, such as the recording
speed, you can do so before you press MENU a second time to confirm.
If you wish to... Then...
Select an input source other ◆ Press the ➛ or ❿ buttons, until the PR selection flashes.
than the tuner LINE IN 1 or LINE IN 2 input ◆ Press the INPUT button one or more times to change the
input source selection.
➢
The input source must be selected before changing any
other value.
Record a programme every day ◆ Press the ➛ or ❿ buttons, until the DAY selection flashes.
(Monday to Sunday) at the same time ◆ Press the ➐ or ❷ buttons, until the DLY (Daily) value is
displayed.
Record a programme every week ◆ Press the ➛ or ❿ buttons, until the DAY selection flashes.
on the same day and at the same time ◆ Press the ➐ or ❷ buttons, until the W- (Week) value is
displayed, followed by the required day.
Example:
W-SA (Weekly Saturday)
Extend the recording time ◆ Press the ➛ or ❿ buttons, until the STOP selection flashes.
◆ Press the ➐ or ❷ buttons to increase or decrease the stop
time.
Select the recording speed ◆ Press the ➛ or ❿ buttons, until the recording speed selection
★
(SV-640B only) flashes.
◆ Press the ➐ or ❷ buttons until the correct indication is
displayed:
• AUTO (Auto Tape Speed Select) : see page 28
• SP (Standard Play)
• LP (Long Play)