Skylink TC-318-7 - Manual (Page 3)

4. ZONE OPERATION - DIMMING
7. PASSWORD
You may control the brightness of lights in a zone.
To brighten up multiple lights in a zone:
1. Press and hold [ ] for 3 seconds, until the red LED flashes 3 times
then stay on.
2. Press and hold the zone number button until the desired brightness is
reached.
To dim down multiple lights in a zone:
1. Press and hold [ ] for 3 seconds, until the red LED flashes 3 times
then stay on.
2. Press and hold the zone number button until the desired brightness is
reached.
All lights in Zone 1 On
Press
Once
Press & Hold 3 sec.
Press & Hold 3 sec.
+
All lights in Zone 1 Off
Press
Once
+
Zone On
Zone Off
5. ALL ON / ALL OFF OPERATION (CONT)
5. ALL ON / ALL OFF OPERATION
TM Press the [ ] button to turn off all the items connected to SkylinkHome
system.
TM Press the [ ] button to turn on all the items connected to SkylinkHome
system.
You may turn on all the lights and appliances with one touch of a button,
or turn them all off as well. All Off function is especially useful when you
are leaving home or going to sleep.
All lights in Zone 1 from Bright to Dim
Press &
Hold
Press & Hold 3 sec.
Press & Hold 3 sec.
+
Press &
Hold
+
All lights in Zone 1 from Dim to Bright
6. ERASING TC SERIES TRANSMITTERS
There are 2 types of receivers and erasing transmitter from these 2 types
of receivers are different. Please follow the erase procedure based on the
receiver you have.
Type A) Self Erase - Model PL-318, PR-318, PA-318, LS-318, WR-001
Self Erase means there is a erase button on the receiver, by pressing this
erase button, all transmitters can be erased.
To erase transmitters from these receivers, simply follow the instructions of
these receivers. The erase procedure does not involve the transmitter.
Type B) Erase by Remote - Model LX-318, MD-318, MR-318, WE-001
Erase by Remote means there is no erase button on the receiver, so a
programmed transmitter is needed in order to erase the memory of the
receiver. You need to transmit a "Erase" code from the Remote. Follow the
instructions below to erase the remote from the receiver.
1. Press the PROG button on the back of the remote.
2. Press and hold a button that is already programmed to the receiver for
at least 2 seconds when the LED is steadily on to transmit the "Erase"
code. Do not release this button until step 4.
3. Put the receiver that you want to erase the transmitter from into
programming mode. Refer to the User's Instructions of that receiver.
4. Once the receiver receives this "Erase" code, the receiver will indicate it
has erased all transmitters, and you may now release the button on the
remote.
Erase Code
Follow steps 2 and 3 above to transmit the "Erase" code when erasing the
remote from Type B receivers.
There is a password function with your TC remote control. You may enable
the password so that the transmitter only functions if a valid password is
entered. This is useful if you would like to have added security so that only
the ones who know the password can operate the receiving devices. If the
password function is disabled, no password is required to operate the
TC remote control.
The password function is disabled at the factory. To determine whether
password function is disabled of enabled:
Press [ ] > Red LED flashes > Password Disabled (Factory Default
Setting)
Press [ ] > Red LED does not flashes > Password Enabled
To factory default password depends on the exact model that you have:
TC-318-7: [1212]
TC-318-10: [2525]
TC-318-14: [2525]
You can assign your personal password between 2 digits to 8 digits.
Follow the instructions below to enable / disable the password function.
TM Note: All zone operations will not activate Model GB-318 Smart Button
® Garage Door Control and Skylink Swing Door Opener.
Note: All On and All Off operations will not activate Model GB-318 Smart
® TM Button Garage Door Control and Skylink Swing Door Opener.
Zone command allows you to operate multiple lights or loads altogether
in the same zone.
To turn on multiple lights / loads in a zone:
1. Press and hold [ ] for 3 seconds, until the red LED flashes 3 times
then stay on.
2. Press the zone number button.
To turn off multiple lights / loads in a zone:
1. Press and hold [ ] for 3 seconds, until the red LED flashes 3 times
then stay on.
2. Press the zone number button.
4. ZONE OPERATION - ON / OFF
Note:
1. During password programming, if you press the wrong button,
start over again after you see led flashes 3 times about 10
seconds.
2. Press button only after LED finishes flashing.
3. The interval between two presses should not be more than 3
seconds.
4. Key 10 can be used as digit “0” in the password.