Sony STR-DA3000ES - Manual (Page 58)

masterpage:Left
filename[\\Nas-data-server\SONY Current jobs\SONY STR-
DA5000ES\DTP\4247188133\424718813STRDA5000ESU\GB08ADD_STR-DA5000ES-U.fm]
58 GB
model name1[STR-DA5000ES]
[4-247-188-13(4)]
There is no sound from the center speaker.
• Make sure the sound field function is on (press
A.F.D., MOVIE or MUSIC).
• Select the CINEMA STUDIO EX mode
(page 34).
• Adjust the speaker level (page 40).
• Make sure the center speaker is set to either
“SMALL” or “LARGE” (page 20).
There is no sound from the surround back
speakers.
• Some discs have no Dolby Digital EX flag even
though the packages have Dolby Digital EX
logos. In this case, select “MATRIX” (page 37).
There is no sound or only a very low-level
sound is heard from the surround/surround
back speakers.
• Make sure the sound field function is on (press
A.F.D., MOVIE or MUSIC).
• Select a CINEMA STUDIO EX mode (page 34).
• Adjust the speaker level (page 22).
• Make sure the surround speakers are set to either
“SMALL” or “LARGE” (page 20).
• Make sure the surround back speaker is set to
either “DUAL” or “SINGLE” (except for STR-
DA3000ES models of area code CEL, TW), or
“YES” (STR-DA3000ES models of area code
CEL, TW only).
There is no sound from sub woofer.
• When all speakers are set to “LARGE” and
“Neo:6 Cinema” or “Neo:6 Music” is selected,
there is no sound from the sub woofer.
The surround effect cannot be obtained.
• Make sure the sound field function is on (press
A.F.D., MOVIE or MUSIC).
• Sound fields do not function for the signals with a
sampling frequency of more than 48 kHz.
Dolby Digital or DTS multi channel sound is
not reproduced.
• Check that the playing DVD, etc. is recorded in
Dolby Digital or DTS format.
• When connecting the DVD player, etc. to the
digital input jacks of this receiver, check the audio
setting (settings for the audio output) of the
connected component.
Recording cannot be done.
• Check that the components are connected
correctly.
• Select the source component with INPUT
SELECTOR.
The FM reception is poor.
• Use a 75-ohm coaxial cable (not supplied) to
connect the receiver to an outdoor FM antenna as
shown below. If you connect the receiver to an
outdoor antenna, ground it against lightning. To
prevent a gas explosion, do not connect the ground
wire to a gas pipe.
Radio stations cannot be tuned in.
• Check that the antennas are connected securely.
Adjust the antennas and connect an external
antenna if necessary.
• The signal strength of the stations is too weak
(when tuning in with automatic tuning). Use direct
tuning.
• Make sure you set the tuning interval correctly
(when tuning in AM stations with direct tuning).
• No stations have been preset or the preset stations
have been cleared (when tuning by scanning
preset stations). Preset the stations (page 27).
• Press DISPLAY so that the frequency appears in
the display.
RDS does not work. *
• Make sure that you’re tuned to an FM RDS
station.
• Select a stronger FM station.
The RDS information that you want does not
appear.
*
• Contact the radio station and find out whether or
not they actually provide the service in question.
If so, the service may be temporarily out of order.
There is no picture or an unclear picture
appears on the TV screen or monitor.
• Select the appropriate input on the receiver.
• Set your TV to the appropriate input mode.
• Move your TV away from the audio components.
AM FM
U
75 COAXIAL
ANTENNA
Receiver
To ground
Ground wire
(not supplied)
Outdoor FM antenna