Kenwood DPX304 - Manual (Page 56)

56
| DPX504U/ DPX404U/ DPX304
DSP Setup
Audio Preset Memory
Registering the value setup by Sound Control.
1
Setup Sound Control
Refer to the following operations to setup the
Sound Control.
-
<Car Type Selection> (page 54)
- <Speaker Setting> (page 54)
- <Car Type Fine Adjustments> (page 55)
- <X’Over Setting> (page 56)
- <Manual Equalizer Control> (page 49)
- <Listening Position Selection> (page 50)
- <Listening Position Fine Adjustments> (page 50)
2
Enter Audio preset memory mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control”
> “Detailed Setup” >
“Preset” > “Preset Memory”.
3
Select the number to put in the memory
Turn the [VOL] knob and press it when the
desired item is displayed.
Select a preset number.
4
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “YES”.
“Memory Completed” is displayed.
5
Exit Function setting mode
Press the [ ] button for at least 1 second.
⁄
• Register 6 patterns of Audio Preset Memory.
• Preset number “1”:
When you press the Reset, all the sources will be the setting
value which is registered.
• Preset number “1” and “2”:
The memory cannot be erased by the Reset button.
• This function cannot be registered when the iPod Equalizer
set in
<Preset Equalizer curve Select> (page 49) .
X’Over Setting
Fine adjusting the following setting values
corresponding to the X’Over values set in the
section
<Speaker Setting> (page 54) .
Display Item Range
“X’Over”
“Front” “FC” Front High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
“SLOPE” Front High Pass Slope
-6, -12, -18, -24 dB/Oct
“Rear” “FC” Rear High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
“SLOPE” Rear High Pass Slope
-6, -12, -18, -24 dB/Oct
“SubWoofer” “FC” Subwoofer Low Pass Filter
30, 40, 50, 60, 70, 80, 90, 100, 120,
150, 180, 220, 250, Through (Hz)
“SLOPE” Subwoofer Slope
-6, -12, -18, -24 dB/Oct
“PHASE” Subwoofer Phase
Reverse (180°)/ Normal (0°)
( : Factory setting)
1
Select the source
Press the [SRC] button.
Select a source other than “STDBY”.
2
Enter Function setting mode
Press the [VOL] knob.
3
Enter X’Over setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Audio Control”
> “Detailed Setup” >
“X’Over”.
4
Select the speaker you want to set
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Front”, “Rear”, or “SubWoofer”.
5
Select the item you want to set
Operation type Operation
Selects the item. Turn the [VOL] knob.
Adjust each item. Press the [ 4] or [¢] button.
Set the value Press the [VOL] knob.
6
Repeat steps 4 to 5 to complete the X’Over
settings.
7
Exit Function setting mode
Press the [ ] button for at least 1 second.
Function of DPX504U