Kenwood TS-2000 - Manual (Page 17)

9
4 GETTING ACQUAINTED
PF
F LOCK A
1
CH1/REC
2
CH2/REC
3
CH3/REC
4
TONE/SEL
5
METER
6
CTCSS/SEL
7
NB/LEVEL
8
AGC/OFF
9
FINE/STEP
. DCS/SEL
0
SHIFT/OFFSET
ENT
SEND
PHONES
MIC
AT
ANT1/2
PROC
LEVEL
VOX
ATT PRE
LEVEL
LEVEL
LEVEL
MANUAL
LO/
WIDTH HI/
SHIFT
N.R.
A.N.
B.C.
F
U
N
C
CALL C.IN
CLR
MAIN
AUTO
CAR
TX MONI
DELAY NAR
REV
MIC
PWR
KEY
LSB
USB
CW
FSK
FM
AM
SUB
DISP
SEL
1MHz CTRL
MR
MG.SEL
M.IN
QUICK MEMO
M/S
REV
TRACE
MAIN
MANUAL RF
AF
SQL
SUB
CH MULTI BC MAIN
GAIN
VFO/CH
MENU TF-
SET
MAIN SUB
SG.SEL
SCAN M VFO M.IN
RIT
CW TUNE 9.6k STA
RIT/SUB
CON
XIT
ALT
SET
CLEAR
P.C.T
_ +
HF/VHF/UHF ALL MODE MULTI BANDER TS-2000
SA TL
A/B
VFO/M
SPLIT
A=B
17
18 15 14
16
!4
Multi-purpose keypad
Consists of 10 keys that are used to enter numeric
data. Also used for the following functions:
• 1/ CH1/REC, 2/ CH2/REC, and 3/ CH3/REC keys
Press to play back or record the CW or voice
messages that are associated with the DRU-3A
Digital Recording Unit {page 89} and the internal
electronic keyer {page 43}.
• 4/ TONE/SEL key
Press to activate the sub-audible Tone function to
access repeaters for FM mode. To select the Tone
frequency, press [FUNC], [4/ TONE/SEL], then
select your desired tone frequency using the
MULTI/ CH control {page 33}.
• 5/ METER key
Press to select the meter scales {page 19}.
• 6/ CTCSS/SEL key
Press to activate the Continuous Tone Coded
Squelch System (CTCSS) function for FM mode.
To select the CTCSS tone frequency, press
[FUNC], [5/ CTCSS/SEL], then select your
desired CTCSS tone frequency using the
MULTI/ CH control {page 35}.
• 7/ NB/LEVEL key
Press to switch the Noise Blanker ON or OFF.
Press [FUNC], [7/ NB/LEVEL] to adjust the Noise
Blanker level {page 57}.
• 8/ AGC/OFF key
Press to adjust the response time of the Automatic
Gain Control. To switch the AGC OFF, press
[FUNC], [8/ AGC/OFF] {page 38}.
• 9/ FINE/STEP key
Press to activate the Fine tuning function to allow
more precise tuning {page 38}.
• •/ DCS/SEL key
Press to activate the Digital Coded Squelch
function for FM mode. To select the DCS code,
press [FUNC], [•/ DCS/SEL], then select your
desired code using the MULTI/ CH control
{page 36}.
• 0/ SHIFT/OFFSET key
Press to switch the Shift function for FM mode ON
or OFF when accessing the repeaters. The Shift
frequency can be manually adjusted by pressing
[FUNC], [0/ SHIFT/OFFSET], then adjusting the
shift frequency value using the MULTI/ CH control
{page 32}.
• ENT key
Press to enter your desired frequency using the
keypad {page 37}.
!5 FUNC key
Press to access the secondary functions that are
assigned to the keys. While FUNC is active, the
FUNC LED lights orange.
!6
MIC/ CAR key
Press to adjust the microphone gain {page 20}.
While the Speech Processor function is ON, it
becomes the Speech Processor output level
adjustment key {page 40}.
Press [FUNC], [MIC/ CAR] to adjust the carrier level
for CW, FSK and AM mode {page 20}.
!7 PWR/ TX MONI key
Press to adjust the output power {page 20}. Press
[FUNC], [PWR/ TX MONI] to monitor your
transmission signal {page 79}.
!8
KEY/ DELAY key
Press to adjust the internal electronic keyer speed.
Press [FUNC], [KEY/ DELAY] to adjust the VOX
delay time or break-in time (Full break-in/ Semi
break-in time) for CW mode {page 42}.