Kenwood TS-2000 - Manual (Page 20)

12
4 GETTING ACQUAINTED
PF
F LOCK A
1
CH1/REC
2
CH2/REC
3
CH3/REC
4
TONE/SEL
5
METER
6
CTCSS/SEL
7
NB/LEVEL
8
AGC/OFF
9
FINE/STEP
. DCS/SEL
0
SHIFT/OFFSET
ENT
SEND
PHONES
MIC
AT
ANT1/2
PROC
LEVEL
VOX
ATT PRE
LEVEL
LEVEL
LEVEL
MANUAL
LO/
WIDTH HI/
SHIFT
N.R.
A.N.
B.C
.
F U
N
C
CALL C.IN
CLR
MAIN
AUTO
CAR
TX MONI
DELAY NAR
REV
MIC
PWR
KEY
LSB
USB
CW
FSK
FM
AM
SUB
DISP
SEL
1MHz CTRL
MR
MG.SEL
M.IN
QUICK MEMO
M/S
REV
TRACE
MAIN
MANUA L
RF
AF
SQL
SUB
CH MULTI BC MAIN
GAIN
VFO/CH
MENU TF-
SET
MAIN SUB
SG.SEL
SCAN M VFO M.IN
RIT
CW TUNE 9.6k STA
RIT/SUB
CON
XIT
ALT
SET
CLEAR
P.C.T
_ +
HF/VHF/UHF ALL MODE MULTI BANDER TS-2000
SA TL
A/B
VFO/M
SPLIT
A=B
47 46 54 55 44 45
53 52 51 50 49 48
$4 RIT/SUB control
After switching the RIT or XIT function ON, turn this
control to select the desired frequency offset
{pages 38, 40}.
Turn to adjust the sub-receiver frequency when the
RIT and XIT functions are switched OFF and the sub-
receiver is switched ON {page 45}.
$5
MANUAL BC control
Turn to adjust the audio notch frequency while the
DSP beat cancel function is set to the manual
frequency adjustment mode {page 56}.
$6 MAIN RF GAIN control
Turn to adjust the radio frequency gain for the main
transceiver {page 18}.
$7
MULTI/ CH control
In VFO mode, rotate to step the operating frequency
up or down {page 37}. In memory channel mode,
rotate to select a memory channel {page 58}. Also
used for selecting Menu numbers when accessing the
Menu mode {page 21} and as a selector to choose
settings for various functions activated by front panel
buttons. The MULTI/ CH LED lights when the
setting(s) can be changed using the MULTI/ CH
control.
$8 MAIN SQL control
Used for muting (“squelching”) the speaker, the head
phones and AF output on ACC2 (13-pin DIN
connector) when no receive signal is present on the
main transceiver {page 19}.
$9
MAIN AF control
Turn to adjust the volume on the main transceiver
{page 19}.
%0
SUB SQL control
Used for muting (“squelching”) the speaker, head
phone and AF output on ACC2 (13-pin DIN
connector) when no receive signal is present on the
sub-receiver {page 46}.
%1 SUB AF control
Press to switch the sub-receiver ON or OFF. When it
is ON, the SUB-receiver LED lights orange.
Turn to adjust the volume for the sub-receiver.
%2
LO/ WIDTH control
Turn clockwise/ counterclockwise to increase/
decrease the value for the low cut-off DSP filter
frequency or the filter bandwidth (CW/ FSK). The
selected value appears on the main dot-matrix
display {page 55}.
%3
HI/ SHIFT control
Turn clockwise/ counterclockwise to increase/
decrease the value for the high cut-off DSP filter
frequency or the Shift frequency. The selected value
appears on the sub dot-matrix display {page 55}.
%4 MAIN band LED
Lights green while the main transceiver’s squelch is
open. Lights red while transmitting on the main
transceiver’s VFO band.
%5 SUB band LED
Lights green while the sub-receiver’s squelch is open.
Lights red while transmitting on the sub-receiver’s
VFO band.