Lexmark N5 - Manual (Page 2)

ii
Edition: September 2002
The following paragraph does not apply to any
country where such provisions are inconsistent with
local law: LEXMARK INTERNATIONAL, INC.,
PROVIDES THIS PUBLICATION “AS IS” WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. Some
states do not allow disclaimer of express or implied
warranties in certain transactions; therefore, this
statement may not apply to you.
This publication could include technical inaccuracies or
typographical errors. Changes are periodically made to
the information herein; these changes will be
incorporated in later editions. Improvements or changes
in the products or the programs described may be made
at any time.
Comments about this publication may be addressed to
Lexmark International, Inc., Department F95/032-2, 740
West New Circle Road, Lexington, Kentucky 40550,
U.S.A. In the United Kingdom and Eire, send to Lexmark
International Ltd., Marketing and Services Department,
Westhorpe House, Westhorpe Marlow Bucks SL7 3RQ.
Lexmark may use or distribute any of the information you
supply in any way it believes appropriate without
incurring any obligation to you. You can purchase
additional copies of publications related to this product by
calling 1-800-553-9727. In the United Kingdom and Eire,
call +44 (0) 8704 440 044. In other countries, contact
your point of purchase.
References in this publication to products, programs, or
services do not imply that the manufacturer intends to
make these available in all countries in which it operates.
Any reference to a product, program, or service is not
intended to state or imply that only that product, program,
or service may be used. Any functionally equivalent
product, program, or service that does not infringe any
existing intellectual property right may be used instead.
Evaluation and verification of operation in conjunction
with other products, programs, or services, except those
expressly designated by the manufacturer, are the user’s
responsibility.
Lexmark and Lexmark with diamond design are
trademarks of Lexmark International, Inc., registered in
the United States and/or other countries.
Other trademarks are the property of their respective
owners.
© Copyright 2002 Lexmark International, Inc. All
rights reserved.
UNITED STATES GOVERNMENT RIGHTS
This software and any accompanying documentation
provided under this agreement are commercial computer
software and documentation developed exclusively at
private expense.
Federal Communications Commission (FCC)
compliance information statement
The Lexmark N5 Wireless Adapter has been tested and
found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device
must accept any interference received, including
interference that may cause undesired operation.
The FCC Class B limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
unplugging the equipment and then plugging it back in,
the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult your point of purchase or service
representative for additional suggestions.
Exposure to Radio Frequency Radiation
The radiated output power of this device is far below the
FCC radio frequency exposure limits. Aminimum
separation of 20 cm (8 inches) must be maintained
between the antenna and any perspns for this deviceto
satisfy the RF exposure requirements of the FCC.
The manufacturer is not responsible for any radio or
television interference caused by using other than
recommended cables or by unauthorized changes or
modifications to this equipment. Unauthorized changes
or modifications could void the user’s authority to operate
this equipment.
Note: To assure compliance with FCC regulations for a
Class B computing device, use a properly shielded and
grounded cable, such as the one provided with this unit,
for USB attach. Use of a substitute cable not properly
shielded and grounded may result in a violation of FCC
regulations.
Any questions regarding this compliance information
statement should be directed to Director of Lexmark
Technology and Services, Lexmark International, Inc.,
740 West New Circle Road, Lexington, KY 40550, (859)
232-3000.
Industry Canada compliance statement
This Class B digital apparatus meets all requirements of
the Canadian Interference-Causing Equipment
Regulations.
This device complies with Industry Canada specification
RSS-210. Operation is subject to the following two
conditions: (1) this device may not cause interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation of the device.
To prevent radio interferencde to the licensed service,
this device is intended to be operated indoors and away
from windows to provide maximum shielding. Equipment
(or its transmit antenna) that is installed outdoors is
subject to licensing.
The installer of this radio equipment must ensure that the
antenna is located or pointed such that it does not emit
RF fields in excess of Health Canada limits for the
general population; consult Safety Code 6, obtainable
from Health Canada’s Web site www.hc-sc.gc.ca/rpb.
Avis de conformité aux normes d’Industrie
Canada
Cet appareil numérique de la classe B respecte toutes
les exigences du Règlement sur le matériel brouilleur du
Canada.
Cet appareil est conforme à la spécification RSS-210
d'Industry Canada. Son fonctionnement est soumis aux