L.L. Bean Weather Finder 0FHF4 - Manual

0FHF4
Weather Finder
USER MANUAL
(FIG. 1)
(FIG. 2)
(FIG. 3)
(FIG. 4)
OVERVIEW
FRONT VIEW (FIG. 1)
1. SNOOZE: Snooze alarm
2. Weather forecast and pressure trend
3. Outdoor temperature readings and trends, and Hi /
Lo temperature alarms
4. Atomic clock / alarm and date
5. Indoor temperature readings and trends
6. MODE: Change settings or display
7. ALARM: View alarm status; set alarm
8. MEM: View current, maximum and minimum
temperature
BACK VIEW (FIG. 2)
1. Wall mount hole
2. RESET: Reset unit to default settings
3. CH: Switch remote sensor display
4. TEMP HI / LO : Change settings or enable / disable
Hi or Lo temperature alarm
5. °C / °F: Select temperature unit
6. / : Increase / decrease setting; activate /
deactivate clock reception signal
7. Battery compartment
8. Table stand
REMOTE SENSOR (FIG. 3)
1. LED status indicator
2. Wall mount hole
3. Battery compartment
4. RESET hole
5. CHANNEL switch
GETTING STARTED
INSERT BATTERIES
1. Remove the battery door.
2. Insert the batteries, matching the polarities (see FIG. 2).
3. Press RESET after each battery change.
NOTE displays when batteries are low.
LOCATION MEANING
Indoor temperature area Main unit batteries low
Outdoor temperature area Sensor batteries low
REMOTE SENSOR
The main unit can collect data from up to 3 sensors.
To set up the sensor:
1. Slide open the battery door.
2. Insert the batteries, matching the polarities.
3. Select a channel, then press RESET (Reset after a
channel or battery change.)
4. Close the battery door.
5. Place the sensor within 30 m (98 ft) of the main unit
using the table stand or wall mount (see FIG. 4).
NOTE Use alkaline batteries for longer usage and
consumer grade lithium batteries in temperatures
below freezing.
SENSOR DATA TRANSMISSION
To search for a sensor:
Simultaneously, press and hold MEM and CH for 2
seconds.
The sensor reception icon in the remote sensor area
shows the status:
ICON
DESCRIPTION
Main unit is searching for sensor(s)
A channel has been found
Sensor 1 data received
and “--.-“ The sensor cannot be found
TIP The transmission range may vary depending on
many factors. You may need to experiment with various
locations to get the best results.
CLOCK
CLOCK RECEPTION
This product is designed to synchronize its clock auto-
matically with a clock signal.
• WWVB-60 signal: within 3200 km (2000 miles) of Fort
Collins, Colorado. Manually set clock to select time
zone (Pacific, Mountain, Central or Eastern).
To enable / disable signal reception:
Press and hold to enable or to disable signal
reception.
NOTE Reception takes 2-10 minutes. If the signal is
weak, it can take up to 24 hours to get a valid signal.
Clock signal reception indicator:
STRONG SIGNAL WEAK SIGNAL NO SIGNAL
MANUALLY SET CLOCK
1. Press and hold MODE.
2. Press or to change the settings. (Press and hold
to change the setting quickly.)
3. Press MODE to confirm.
4. The settings order is: time zone offset, hour, minute,
year, month, day and language.
NOTE Select the time zone: (PA) Pacific, (EA) Eastern,
(CE) Central or (MO) Mountain.
NOTE The language options are English (E), German
(D), French (F), Italian (I), and Spanish (S).
To select display mode:
Press MODE to choose between clock with seconds
and clock with weekday.
ALARM
To set the alarm:
1. Press ALARM to view display. shows when the
alarm time is displayed.
2. Press and hold ALARM.
3. Press / to set hour / minute. (Press and hold to
change the setting quickly.)
4. Press ALARM to confirm. indicates alarm is ON.
To toggle alarms ON / OFF:
1. Press ALARM to display alarm time.
2. Press ALARM again to turn alarm ON / OFF.
To silence the alarm:
• Press SNOOZE to silence it for 8 minutes.
OR
• Press any other key to turn the alarm off and activate
it again after 24 hours.
WEATHER FORECAST
This product forecasts the next 12 to 24 hours of
weather within a 30-50 km (19-31 mile) radius with a
75% accuracy.
Sunny Partially Cloudy Cloudy Rainy
TEMPERATURE
To toggle temperature unit:
Slide °C / °F to the desired setting.
To view outdoor sensors readings:
Press CH.
To auto-scan between sensors:
Press and hold CH to display each sensor’s data for
3 seconds.
To end press CH or MEM.
To toggle between current, minimum and maximum
records for the selected outdoor sensor and indoor
(main unit) sensor:
Press MEM repeatedly.
To clear the records:
Press and hold MEM.
WEATHER TRENDS
The pressure trend icons are based on recent sensor
readings.
RISE STEADY FALL
HI / LO TEMP ALARMS
Temperature alerts can be set to sound if sensor set
to Channel 1 records above or below a temperature
of your choice.
To set alarm ON / OFF:
1. Press and hold TEMP HI / LO .
2. Use or to change settings.
3. Press TEMP HI / LO to confirm.
4. The setting order is: alarm type, alarm ON / OFF, alarm
temperature value. LO / HI will appear above the
temperature to indicate the alarm is on.
To silence the Hi / Lo alarm:
Press any key . The alarm resets automatically and will
resound if the hi / lo temperature selected is recorded
again.
RESET
Press RESET to return to the default settings.
PRECAUTIONS
• Do not subject the unit to excessive force, shock, dust,
temperature or humidity
• Do not cover the ventilation holes with any items such
s newspapers, curtains etc.
• Do not immerse the unit in water. If you spill liquid
over it, dry it immediately with a soft, lint-free cloth.
• Do not clean the unit with abrasive or corrosive
materials.
• Do not tamper with the unit’s internal components.
This invalidates the warranty.
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
BAR186A_IM_LLB_EN_NO R_R0 20.11.2007, 10:23 AM 1