Panasonic DMR-EX78 - Manual (Page 23)

23
RQT9088
Copying from a video cassette recorder
e.g., Connecting to the AV3 or DV input terminals on the front
You can also connect to the AV4 input terminals on the rear.
≥Turn off the unit and other video equipment before connecting.
If the audio output of the other equipment is monaural
Connect to L/MONO on the AV3 input terminals at the front.
§ The S VIDEO terminal achieves a more vivid picture than the
VIDEO terminal.
When recording from the unit’s DV terminal
≥Select the type of audio recording from “Audio Mode for DV Input”
in the Setup menu ( ➡ 62).
≥When recording from DV equipment (e.g., digital video camcorder),
you can record audio/video recordings from DV tape only.
≥When “Rec for High Speed Copy” ( ➡ 61) is set to “On” and you
make a copy, the copy will be made using the picture size selected
in “Aspect for Recording” (
➡ 61) of the Setup menu.
About the aspect when recording a programme ( ➡ 20)
[Note]
≥If it becomes time for a timer recording to start while copying, the
recording will start and the copying will stop.
≥If video is copied from another piece of equipment to this unit, then
the video quality will be degraded.
[HDD] [RAM] [-R] [-RW‹V›] [+R] [+RW]
Preparation
≥Press [DRIVE SELECT] to select the HDD or DVD drive.
≥Press [REC MODE] to select the recording mode.
≥When recording bilingual programmes ( ➡ 20, Important notes for
recording)
≥When the output signal from the external equipment is NTSC,
change the “TV System” to “NTSC” in the Setup menu ( ➡ 64).
This unit cannot record NTSC signals to discs that already have
PAL signal recordings. (However, both types of programmes can
be recorded onto the HDD.)
≥To reduce noise in input from a video cassette recorder, set “Input
NR” to “On” in the on-screen menu ( ➡ 54).
≥Check the time on the unit is correct.
1
While stopped
Press [INPUT SELECT] to select the
input channel for the equipment you
have connected.
e.g., If you have connected to AV3 input terminals, select “A3”.
2
Start play on the other equipment.
3
When you want to start recording
Press [ ¥ REC].
Recording starts.
To skip unwanted parts
Press [
;] to pause recording. (Press again to restart recording.)
To stop recording
Press [
∫].
≥Using Flexible Recording ( ➡ 22), you can record the content of a
video cassette (approx. 1–8 hours) to a 4.7 GB disc with the best
possible quality of recording without wasting disc space.
[HDD] [RAM] [-R] [-RW‹V›] [+R] [+RW]
[HDD] [RAM] When the “DV Auto Rec” function is used, programmes
are recorded as a title while at the same time chapters are created at
each break in the images and the playlist is created automatically.
Preparation
1 Turn off the main unit and DV equipment, then connect the
equipment with the unit’s DV input terminal ( ➡ left).
2 Turn on the main unit.
≥When the output signal from the external equipment is NTSC,
change the “TV System” to “NTSC” in the Setup menu ( ➡ 64).
1
Turn on the DV equipment, and pause
play at the point you want recording to
start.
The following screen appears.
≥When the screen is not displayed
2
Press [ 2, 1] to select “Rec to HDD”
or “Rec to DVD” and press [OK].
3
Press [REC MODE] to select the
recording mode.
4
Press [ 2, 1] to select “Rec” and
press [OK].
Recording starts.
When recording finishes
The confirmation screen appears. Press [OK] to finish DV automatic
recording.
To stop recording
Press [
∫].
[Note]
≥Only one piece of DV equipment (e.g., digital video camcorder) can
be connected to the unit via the DV input terminal.
≥It is not possible to operate the unit from the connected DV equipment.
≥The DV input on this unit is for use with DV equipment only. (It
cannot be connected to a computer, etc.)
≥The DV equipment name may not be shown correctly.
≥Depending on the DV equipment, the images or audio may not be
input properly.
≥The date and time information on the tape of the DV equipment will
not be recorded.
≥You cannot record and play simultaneously.
Manual recording
Almost all videos and DVD-Video on sale have been treated
to prevent illegal copying. Any software that has been so
treated cannot be recorded using this unit.
OPEN / CLOSE
REC
L/MONO - AUDIO- R VIDEO S VIDEO DV IN
AV3 IN
Audio/Video
cable
S Video
cable §
Yellow White Red
This unit
Other video equipment
Connect to Audio/Video output terminals.
DV cable
(IEEE 1394, 4-pin)
DV automatic recording (DV Auto Rec)
After performing step 1
1 Press [DRIVE SELECT] to select the HDD or DVD drive.
2 Press [FUNCTION MENU].
3 Press [
3, 4] to select “To Others” and press [OK].
4 Press [ 3, 4] to select “DV Auto Rec” and press [OK].
➡ Go to step 3 (➡below)
If the DV automatic recording function does not work properly,
check the connections and DV equipment settings, and turn the
unit off and back on.
If that does not work, follow the instructions for manual
recording (
➡ left).
DV Auto Rec
Rec to HDD Rec to DVD Cancel
DV unit is connected.
Record from the DV unit?
OK RETURN
SELECT
Ad
v
a
n
ced
r
eco
rd
in
g
/Co
p
y
in
g
f
ro
m
a vi
d
e
o
cas
set
te
r
eco
rd
er
DMREX78&88GN-RQT9088-L_eng.book 23 ページ ２００８年４月１日 火曜日 午後６時３８分