Panasonic BT-LH2600WE - Manual (Page 30)

30
REMOTE Specifications
REMOTE operation is possible on this monitor using the GPI/RS-232C terminal.
Each of the items in the GPI screen are compatible with the following terminals.
You can assign functions to each terminal in the menu GPI screen (J page 26).
The functions assigned to each terminal operate when the GND (5 Pin) is connected (ON) or open (OFF).
g Operating conditions
Level operation: operates when GND is connected.
Edge operation: operates when GND changes from
open to connected.
• If you have assigned a level operation function to
more than one terminal, the function operates as long
as one of the terminals is connected.
*1 When the 16:9 marker and 4:3 marker are simultaneously selected and activated on the 16:9 aspect display, both markers are displayed.
*2 When the 16:9 marker and 4:3 marker are simultaneously displayed, the background selected with the 16:9 marker is controlled.
*3 When both “R-TALLY” and “G-TALLY” are ON at the same time, the tally color becomes orange.
*4 This is only enabled when “RGB-VIDEO” is selected in “YP
B
P
R
/RGB” in the “INPUT SELECT” menu.
GPI terminal
Pin number Signal
1 GPI1
2 GPI2
GPI Terminal (9P) 3 GPI3
4 GPI4
5 GND
6 GPI5
7 GPI6
8 GPI7
9 GPI8
Assignment items Function Operating conditions
UNDEF No settings (no terminal assignment functions) —
MARKER1
ON/OFF
*1
Switches the marker display of the marker decided in
“GPI PRESET1” (J page 17) in the “MARKER” menu.
Level operation
(Connected: ON, Open: OFF)
MARKER2
ON/OFF
*1
Switches the marker display of the marker decided in
“GPI PRESET2” (J page 17) in the “MARKER” menu.
Level operation
(Connected: ON, Open: OFF)
MARKER
BACK HALF
*2
Reduces the brightness of the background outside the
marker displayed in “GPI PRESET1” (J page 17) by 50%.
Level operation
(Connected: ON, Open: OFF)
MARKER
BACK BLACK
*2
Reduces the brightness of the background outside the
marker displayed in “GPI PRESET1” (J page 17) to 0%.
Level operation
(Connected: ON, Open: OFF)
CENTER MARKER
Switches the center marker display ON/OFF.
(When other markers are being displayed, this is
superimposed on the other markers)
Level operation
(Connected: ON, Open: OFF)
INPUT SEL. VIDEO
Switches the input system to VIDEO. Edge operation
INPUT SEL. Y/C Switches the input system to Y/C. Edge operation
INPUT SEL. SDI1
Switches the input system to SDI1. Edge operation
INPUT SEL. SDI2 Switches the input system to SDI2. Edge operation
INPUT SEL.
YP
B
P
R
/RGB
Switches the input system to YP
B
P
R
/RGB. Edge operation
SD ASPECT Sets the aspect ratio settings when using SD signal
input. (Disabled when using HD signal and PC signal)
Level operation
(Connected: 16:9, Open: 4:3)
SCAN You can switch the scan mode between “UNDER”
and “NORMAL”. (Disabled when using PC signal)
Level operation (Connected: UNDER,
Open: NORMAL)
R-TALLY *3 Lights the red tally. Level operation
(Connected: ON, Open: OFF)
G-TALLY *3 Lights the green tally. Level operation
(Connected: ON, Open: OFF)
MONO Switches between color and monochrome
(MONO). (Disabled when using PC signal)
Level operation (Connected:
Monochrome, Open: Color)
GAMMA SEL. FILM Used to switch the gamma characteristic to the
FILM mode.
Level operation (Connected: FILM
mode, Open: STANDARD mode)
GAMMA SEL.
STDIO/PST
Used to switch the gamma characteristic to the
STDIO/PST mode.
Level operation (Connected: STDIO/
PST mode, Open: STANDARD mode)
RGB SYNC *4 Used to select SYNC at the time of RGB-VIDEO
input.
Level operation
(Connected: EXT, Open: G-ON)