Pioneer DJM-700-S - Manual (Page 20)

EFFECT FUNCTIONS
20
En
EFFECT PARAMETERS
Beat Effect (*1)
(*1) When the effect channel selector is set to [ CF.A ], [ CF.B ], or [ MASTER ], even if the effect monitor is turned ON, if the selected channel’s
sound is not output to the master output, the effect sound will not be heard.
(*2) When effect is disabled (OFF), the effect sound will not be heard, even if monitor is set to effector.
Name Beat Switch Parameter Parameter 1 (TIME dial) Parameter 2
(LEVEL/DEPTH dial) contents
Contents Setting Range (unit)
1 DELAY Sets delay time of 1/8 to 16/1
per 1 beat of BPM time. Sets delay time. 1 to 4 000 (ms) Sets balance between original and
delay sound.
2 ECHO (*2) Sets delay time of 1/8 to 16/1
per 1 beat of BPM time. Sets delay time. 1 to 4 000 (ms) Sets balance between original sound
and echo sound.
3 TRANS Sets cut time of 1/16 to 16/1
per 1 beat of BPM time. Sets effect time. 10 to 16 000 (ms) Sets balance between original sound
and effect sound.
4 FILTER Cycle of cutoff frequency shift
is set in unit of 1/4 to 64/1
relative to 1 beat of BPM. Sets cycle for cutoff
time shift. 10 to 32 000 (ms) Amount of effect increases when
dial is turned clockwise.
5 FLANGER Cycle of flanger shift is set in
units of 1/4 to 64/1 relative to
1 beat of BPM. Sets cycle for
flanger effect shift. 10 to 32 000 (ms) Amount of effect increases when
dial is turned clockwise. When dial is
turned fully counterclockwise, only
original sound is output.
6 PHASER Cycle of phaser effect shift is
set in units of 1/4 to 64/1
relative to 1 beat of BPM. Sets cycle for phase
effect shift. 10 to 32 000 (ms) Amount of effect increases when
dial is turned clockwise. When dial is
turned fully counterclockwise, only
original sound is output.
7 REVERB (*2) Amount of reverberation is set
from 1 % to 100 %. Sets amount of
reverberation effect. 1 to 100 (%) Sets balance between original sound
and effect sound.
8 ROBOT Sets pitch of robot sound
effect within range of –100 %
to +100 %. Sets pitch of robot
sound effect. –100 to +100 (%) Amount of effect increases when
dial is turned clockwise.
9 CRUSH Cycle of crush effect
movement is set to 1/4 to 64/1
relative to a single beat of
BPM. Sets cycle for crush
effect shift. 10 to 32 000 (ms) Amount of effect increases when
dial is turned clockwise. When dial is
turned fully counterclockwise, only
original sound is output.
10 ROLL (*2) Effect time is set as 1/16 to 16/1
relative of 1 beat of BPM. Sets effect time. 1 to 4 000 (ms) Sets balance of original sound and
roll sound.
11 REVERSE
ROLL (*2)
Effect time is set as 1/16 to 16/1
relative of 1 beat of BPM. Sets effect time. 1 to 4 000 (ms) Sets balance of original sound and
roll sound.
12 UP ROLL (*2) Effect time is set as 1/16 to 16/1
relative of 1 beat of BPM. Sets effect time. 1 to 4 000 (ms) Sets balance of original sound and
roll sound.
13 DOWN ROLL
(*2)
Effect time is set as 1/16 to 16/1
relative of 1 beat of BPM. Sets effect time. 1 to 4 000 (ms) Sets balance of original sound and
roll sound.
14 SEND/
RETURN
— — — Sets volume of RETURN input
sound.
01_DJM-700_En.book 20 ページ ２００７年７月１０日 火曜日 午後８時５１分