Panasonic SL-PD9 - Manual (Page 4)

4
Before use
RQT5763
Connections
A Before making connections, be sure that the power of this unit
and all other system components is turned off.
Conserving power
The unit consumes 1 W even when it is turned off with [ /I, POWER].
To save power when the unit is not to be used for a long time,
unplug it from the household AC outlet.
Note
Although the figure shows the AC power supply cord being
connected to a household AC outlet, if the amplifier (or receiver) is
equipped with a AC outlet, connect the cord to that outlet.
Digital connection
Remove the dust-protection cap and connect this unit to other
digital equipment with an optical fiber terminal, such as a receiver
or digital surround processor.
• Leave the cap attached when this terminal is not being used.
For your reference
If you have DTS format CDs, you can enjoy six channel playback
by connecting this unit to a receiver or digital surround processor
that has a DTS decoder.
Note
Use only the optical fiber terminal when playing back DTS format
discs. DTS signals can only be correctly output through the digital
terminal. Connection through the stereo LINE OUT terminals will
result in noise and could possibly damage your speakers.
• DTS is a trademark of Digital Theater Systems, L.P.
Preparing the remote control
SL-PD9 only
Battery installation
Use of batteries
• Align the poles (+ and –) properly when inserting the batteries.
• Do not mix old and new batteries, or different types of batteries.
• Do not recharge ordinary dry cell batteries.
• Do not heat or disassemble the batteries. Do not allow them to
contact flame or water.
• Remove the batteries if the unit is not to be used for a long time.
• Do not keep together with metallic objects such as necklaces.
• Do not use rechargeable type batteries.
• Do not use batteries if the covering has been peeled off.
Mishandling of batteries can cause electrolyte leakage which can
damage items the fluid contacts and may cause a fire.
If electrolyte leaks from the batteries, consult your dealer.
Wash thoroughly with water if electrolyte comes in contact with any
part of your body.
Correct method of use
Operation notes
• Aim the remote control’s transmission window toward the unit’s
sensor. Avoid any obstacles.
• Be sure the transmission window and the unit’s sensor are free
from dust. Excessive dust might affect performance.
• Do not expose the remote control signal sensor to direct sunlight
or to the bright light of a fluorescent light.
To prevent damage
• Never place heavy items on top of the unit.
• Do not disassemble or reconstruct the unit.
• Do not spill water or other liquids into the unit.
A
B
C
D
4
7
2
5
8
3
6
9
0
1
10 10
OPEN CLOSE
POWER
/ I
REPEAT SPIRAL RANDOM MODE
TIME MODE
EDIT GUIDE ID SCAN
PROGRAM MODE DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 DISC SKIP
L
R
CD
OPTICAL
OUT AC IN
R L
LINE OUT
Amplifier or receiver (not included)
To household AC
outlet
(AC 120 V, 60 Hz)
Optical-fiber cable
(not included)
Receiver
(not included)
1
2
3
Remote control signal sensor
30˚ 30˚
About 7 meters in
front of the signal
sensor
Transmission
window
R6, AA, UM-3
ID SCAN CLEAR RECALL
REPEAT SPIRAL
7
DISC SKIP
DISC
TIME MODE
SKIP
SEARCH
6
8 9
2 3
4 5
1 DISC 1
DISC 4
DISC 2 DISC 3
DISC 5
0
10
OPEN/
CLOSE
PROGRAM MODE
RANDOM MODE
This unit
CD or AUX terminals
CD
OPTICAL
OPTICAL
OUT
This unit
Dust-protection cap
Stereo connection cable (included)
White (L)
Red (R)
B
C
D