Philips MAGIC 5 ECO PPF 695 - Manual (Page 29)

Fax 29
EN
Broadcasting
Broadcasting
You can send one fax to multiple recipients in succession.
Entering Recipients Individually
1 Insert the document.
2 Press
OK, 34 and OK. The document is now
read.
3 Enter the desired number using the numeric keypad or
select a saved entry.
4 Confirm with
OK.
5 Enter the next telephone numbers.
6 Confirm with
OK. You can enter up to 25 recipients.
7 Press
START. The device transmits the fax message
successively to all recipients.
Sending a Fax to a Group
1 Insert the document.
2 Press
OK, 13 and OK.
3 Use
[ to select the group to which you would like to
send a fax.
4 Confirm with
OK.
5 Using
[ select
SEND FAX? .
6 Confirm with
OK.
Transmission to Multiple Recipients
Delayed Fax Transmission
Delayed Fax Transmission
If you would like to make use of the lower telephone tariffs
or if the recipient can be reached at some specific time on-
ly, you can send the fax at a later time – within 24 hours.
1 Insert the document.
2 Press
OK, 33 and OK.
3 Enter the time, at which the document should be trans-
mitted, e.g.
14 00 for 2 pm.
4 Confirm with
OK.
5 Enter the desired number using the numeric keypad or
select a saved entry.
6 Selecting a saved entry: Confirm the selected en-
try using
OK.
7 Press
START. The device goes into standby mode and
transmits the fax at the entered time. You can continue
to make telephone calls and receive faxes.
Sending Fax Later
Receiving Faxes
Fax Reception
If you have not changed the factory settings, received faxes
will be printed out automatically. If no paper or no ink
film is inserted, the machine saves the incoming faxes. The
ä - button blinks. Once paper or a new ink film is
inserted, the saved faxes are printed out.
Paper Error
Full Message Memory
If the message memory is full, no additional messages can
be received. A warning appears on the display. Observe the
information in the technical data.
Delete Fax Memory Service Code
Receiving fax automatically (fax
only reception mode)
Function is not supported in all countries and networks (Function is not supported in all countries and
networks)
Only Fax Reception
You should select this mode if you primarily receive faxes
at your device. In the fax only reception mode (
F on the
display) the device rings twice. Then the fax reception
switches on. You can only accept an incoming telephone
call whilst it is ringing. You cannot switch on the answer-
ing machine in this mode (also see chapter Setting the Fax
Switch, page 38).
Receiving fax manually
Select manual reception under number of rings of the fax
switch (see Chapter Setting the Fax Switch, page 38). The
device will not receive faxes on its own. This setting is use-
ful, when you want to receive faxes via a modem connected
to a computer.
Receiving fax manually
You can start fax reception manually, by pressing
START.
Polling Faxes
Fax Polling
With the fax polling function, you can retrieve faxes that
lie ready in the dialled fax machine. You can also provide
documents on your machine to be polled by others.
Polling Faxes Directly
1 Enter the desired number using the numeric keypad or
select a saved entry.
2 Hold
START pressed (for at least two seconds).
Polling Secure Faxes
Secure Fax Polling
With this function, you can poll faxes that are protected
with a code.
1 Press
OK, 31 and OK.
2 Enter the code.
3 Confirm with
OK.
4 Enter the desired number using the numeric keypad or
select a saved entry.
5 Press
START.
If your machine cannot reach a recipient, the fax
message is sent to the other recipients. After the ma-
chine has called all recipients, it once again dials the
numbers that previously could not be reached.
Press
STOP to eject the document. This interrupts
the standby mode.
Check whether you have inserted and clamped in the
paper correctly. The lever on the right next to the pa-
per feed mechanism must be pushed back.
If there are problems with printing out saved fax
messages, a service code is available (see also section
Service, page 50).