Midi settings, Midi messages, Midi channel setting – Pioneer DJM-600 User Manual
Page 20
20
MIDI SETTINGS
MIDI is an acronym for “Musical Instrument Digital Interface” and
refers to a protocol developed for the exchange of data between
electronic instruments and computers.
A MIDI cable is used to connect components equipped with MIDI
connectors to enable the transmission and receipt of data.
The DJM-800 uses the MIDI protocol for transmitting and receiving
data about component operation and BPM (timing clock).
MIDI START
/STOP
TIME
MIDI OUT
DJM-800
OUT
BPM
=120
BPM
=120
IN
IN
DJ CD Player
MIDI sequencer
Audio
1. Use a commercially available MIDI cable to connect the
DJM-800’s MIDI OUT connector to the MIDI sequencer’s
MIDI IN connector.
¶ Set the MIDI sequencer’s synch mode to “Slave”.
¶ MIDI sequencers that do not support MIDI timing clock cannot
be synchronized.
¶ Synch may not be achieved if the track’s BPM cannot be
detected and measured stably.
¶ BPM values set with the TAP mode can also be used to output
the timing clock.
2. Press the MIDI START/STOP button.
¶ The MIDI timing clock output range is 40 to 250 BPM.
Note:
¶ Accurate measuring of BPM may be impossible with some tracks.
[MIDI Channel Setting]
The MIDI channel (1 to 16) can be set and stored in memory.
1. While holding the MIDI START/STOP button depressed,
set the power switch to ON.
¶ The display will show [MIDI CH SETTING] and the unit will
enter the MIDI setting mode.
2. Rotate the TIME dial to select the MIDI channel.
3. Press the MIDI START/STOP button.
¶ The selected MIDI channel will be recorded.
4. Set power to OFF.
MIDI MESSAGES
CH1
CH2
CH3
TRIM
HI
MID
LOW
COLOR
CUE
FADER
CF ASSIGN
TRIM
HI
MID
LOW
COLOR
CUE
FADER
CF ASSIGN
TRIM
HI
MID
LOW
COLOR
CUE
FADER
CF ASSIGN
VR
VR
VR
VR
VR
BUTTON
VR
SW
VR
VR
VR
VR
VR
BUTTON
VR
SW
VR
VR
VR
VR
VR
BUTTON
VR
SW
Bn
01
dd
Bn
02
dd
Bn
03
dd
Bn
04
dd
Bn
05
dd
Bn
46
dd
Bn
11
dd
Bn
41
dd
Bn
06
dd
Bn
07
dd
Bn
08
dd
Bn
09
dd
Bn
0A
dd
Bn
47
dd
Bn
12
dd
Bn
42
dd
Bn
0C
dd
Bn
0E
dd
Bn
0F
dd
Bn
15
dd
Bn
16
dd
Bn
48
dd
Bn
13
dd
Bn
43
dd
0 to 127
0 to 127
0 to 127
0 to 127
0 to 127
OFF=0, ON=127
0 to 127
0, 64, 127
0 to 127
0 to 127
0 to 127
0 to 127
0 to 127
OFF=0, ON=127
0 to 127
0, 64, 127
0 to 127
0 to 127
0 to 127
0 to 127
0 to 127
OFF=0, ON=127
0 to 127
0, 64, 127
Category
Switch Name
Switch Type
MIDI Message
Comments
MSB
LSB
MIDI SETTINGS
SYNCHRONIZING AUDIO SIGNALS
TO EXTERNAL SEQUENCER, OR
USING DJM-800 INFORMATION TO
OPERATE AN EXTERNAL
SEQUENCER