Pioneer BDP-320 - Manual (Page 42)

06
42
En
 Changing the speaker setup
Set whethe r or not speakers are connected to an AV
receiver or amplifier, etc., their size and their crossover
f
requency. This setting is only valid for the AUDIO OUT
te rminals.
When the re are no speakers whose speaker size is set to
Small, select Bypass for the crossover frequency.
When the re are speakers whose speaker size is set to
Small, select the crossover frequency (Bypass cannot be
selected).
Caution
• The Speaker Setup cannot be selected when Audio
Output Mode is set to 2 Channel. Change the
setting to
Multi-channel (page 38).
1 Select and set Speakers  Speaker Setup  Next
Screen.
Use
/ to select, then press ENTER.
2 Select the speaker and change the setting.
Use
/ to select, then use / to change the setting.
• L/R (front left and right speakers): Large/Small
• C (center speaker): Large/Small/None
• SL/SR (left and right surround speakers): Large/
Small/None
• SBL/SBR (left and right surround back speakers):
Large/Small/None
• SW (subwoofer): Yes/No
• Crossover: Bypass/50 Hz/80 Hz/100 Hz/150 Hz
Note
• De pending on the combination of settings of the
diffe rent speakers, the settings of speakers other than
the one you have changed may also change
automatically.
• When a subwoofe r with a filter bypass function is
connected and the re is no speaker whose speaker
size is set to Small, if the subwoofer’s filter is set to be
by passed, the player’s high precision digital filter is
used. In this case, set the c rossover frequency to
something othe r than Bypass.
• U pon purchase, the crossover frequency is set to
Bypass.
 Adjusting the distance of the
different speakers
Adjust the distance between you and the diffe rent
s peakers. This setting is only valid for the AUDIO OUT
te rminals.
Caution
• This cannot be selected when Audio Output Mode
is set to 2 Channel. Change the setting to Multi-
channel (page 38).
• Speaker Distance of the speakers set to None or No
at
Speaker Setup cannot be adjusted (above).
1 Select and set Speakers  Speaker Distance 
Next Screen.
Use
/ to select, then press ENTER.
2 Select the speaker and adjust the distance.
Use / to select, then use / to adjust.
• The distance of all the s peakers can be set to between
1 inch and 45 feet, in units of 1 inch.
 Adjusting the output level of the
different speakers (Channel Level)
Adjust each out put level of the different speakers by using
test tones. This setting is only valid fo r the AUDIO OUT
te rminals.
Caution
• This cannot be selected when Audio Output Mode
is set to 2 Channel. Change the setting to Multi-
channel (page 38).
• Channel Level of the speakers set to None or No at
Speaker Setup cannot be adjusted (above).
• Test tones a re output. Lower the volume of the device
connected to the player.
1 Select and set Speakers
 Channel Level, then
Fix or Variable.
Use
/ to select, then press ENTER.
• Fix – The output level of all the speakers is set to the
maximum.
• Variable – The output level of all the speakers is set
6.0 dB lowe
r than when Fix is selected. From this
point, the output levels of the L, C, R, SL, SR, SBL, SBR
and SW speakers can be adjusted within the range of
–6.0 dB to +6.0 dB.
If you have selected Variable, proceed to step 2.
L/R
C
SL/SR
SBL/SBR
SW
Large
Large
Large
Large
Yes
Crossover Bypass
Speaker Setup
BD PLAYER
L
C
R
SR
SBR
SBL
SL
SW
Speaker Distance
BD PLAYER
10’00”
10’00”
10’00”
10’00”
10’00”
10’00”
10’00”
10’00”
320_UXJCA_EN.book 42 ページ ２００９年２月１３日 金曜日 午後４時２６分