Pioneer VSX-1015-K - Manual (Page 69)

Additional information 12
69
En
No sound
Symptom Cause Remedy
No sound is output when an
input source is selected.
No sound output from the front
speakers. • Improper connections. • Make sure you have properly connected the component
to the corresponding input on the back of the receiver
(see
Connecting up on page 14).
• Sound is muted or the volume is turned
down. • Press MUTE or adjust the volume accordingly.
• Speakers are turned off or selected
improperly with the
SPEAKERS switch.
• Press SPEAKERS to select the proper speaker set (see
Switching the speaker system on page 60).
• The input signal type is incorrect. • Press SIGNAL SELECT to select the proper input signal
(see Choosing the input signal on page 35).
• The multichannel analog inputs are
selected. • Press MULTI CH IN again (see Selecting the
multichannel analog inputs on page 39).
• The front speakers aren’t connected
properly. • See Connecting the speakers on page 20 to connect
them properly.
No sound from the surround or
center speakers. • Speaker settings are incorrect. (for
example, they have been set to
NO ).
• Check you speaker settings in Speaker Setting on
page 46.
• The surround and/or center levels are
turned down. • Check the levels in Channel Level on page 47.
• The surround and/or center speakers are
disconnected. • Check Connecting the speakers on page 20 to make sure
the speakers are connected correctly.
• The STEREO listening mode has been
selected.
• Choose a surround listening mode (see Listening in
surround sound on page 31).
No sound from surround back
speakers. • Surround back speakers are set to NO . • Set the surround back speakers to LARGE or SMALL
(see Speaker Setting on page 46).
• The Extended mode is switched to AUTO or
OFF .
• Set to Extended ON (see Using the surround back
channel (Extended mode) on page 36).
• The source is not a 6.1 channel playback
source. • Switch the Extended mode to Extended ON (see Using
the surround back channel (Extended mode) on page 36)
and choose a surround listening mode (see Listening in
surround sound on page 31).
• The surround back speakers are
disconnected. • Check Connecting the speakers on page 20 to make sure
the speakers are connected correctly.
• The surround back channel is on the 1
speaker setting, and your speaker is
connected to the right channel output. • Connect the speaker to the surround back left channel
output (
Connecting the speakers on page 20).
• The Extended mode is switched to AUTO
and the Dolby Surround EX / DTS ES software
you’re playing has no flag to indicate it is 6.1
compatible.
• You can still listen with surround back sound by setting
to
Extended ON ( Using the surround back channel
(Extended mode) on page 36).
No sound from subwoofer. • The subwoofer is disconnected or switched
off. • Connect or switch on the subwoofer (see Connecting
the speakers on page 20).
• Make sure the sleep function on your subwoofer isn’t
activated.
• The subwoofer's settings are incorrect. • Set the subwoofer (see Speaker Setting on page 46) to
YES or PLUS .
• The crossover frequency is set too low. • Set the crossover frequency to a (higher) frequency that
matches your speaker characteristics (see
Crossover
Network on page 47)
• There is very little low frequency information
in your source. • Change your subwoofer setting to one of the following in
the
Speaker Setting on page 46:
Front: SMALL / Subwoofer: YES
Front: LARGE / Subwoofer: PLUS
• The LFE channel is switched off. • See LFE Attenuator Setup on page 67 to adjust the
setting.
• The subwoofer's levels are too low. • See Channel Level on page 47 to check the speaker
levels.
• Check the volume control on the subwoofer to make
sure it is turned up.
VSX_1015.book.fm 69 ページ ２００５年３月７日 月曜日 午後７時０分