Panasonic RC-CD300 - Manual (Page 8)

1. Damage requiring service—The unit should be serviced by qualified
service personnel if:
1. (a) The AC power supply cord or AC adaptor has been damaged; or
1. (b) Objects or liquids have gotten into the unit; or
1. (c) The unit has been exposed to rain; or
1. (d) The unit does not operate normally or exhibits a marked change in
performance; or
1. (e) The unit has been dropped or the cabinet damaged.
2. Servicing—Do not attempt to service the unit beyond that described in
these operating instructions. Refer all other servicing to authorized ser-
vicing personnel.
3. Replacement parts—When parts need replacing ensure the servicer
uses parts specified by the manufacturer or parts that have the same
characteristics as the original parts. Unauthorized substitutes may re-
sult in fire, electric shock, or other hazards.
4. Safety check—After repairs or service, ask the servicer to perform
safety checks to confirm that the unit is in proper working condition.
Product information
For product information or assistance with product operation:
In the U.S.A., contact the Panasonic Customer Call Center at 1-800-211-
7262, or e-mail consumerproducts @panasonic.com, or the website
(http://www.panasonic.com).
In Canada, contact the Panasonic Canada Inc. Customer Care Centre at
905-624-5505, or visit the website (www.panasonic.ca), or an authorized
Servicentre closest to you.
8
Product service
DATE OF PURCHASE
DEALER NAME
DEALER ADDRESS
TELEPHONE NUMBER
CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
CAUTION:
TO PREVENT ELECTRIC SHOCK MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
User memo:
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR PRODUCT DAMAGE, DO NOT EX-
POSE THIS APPARATUS TO RAIN, MOISTURE,
DRIPPING OR SPLASHING AND THAT NO OB-
JECTS FILLED WITH LIQUIDS, SUCH AS VASES,
SHALL BE PLACED ON THE APPARATUS.
THE FOLLOWING APPLIES ONLY IN THE U.S.A.
Frequency range
FM: 87.5–108.0 MHz
AM: 525–1710 kHz
Sampling frequency 44.1 kHz
Decoding 16 bit linear
Beam source Semiconductor laser
(wavelength 780 nm)
No. of channels 2 channel, stereo
Wow and flutter Less than possible measurement
data
DA converter MASH (1 bit DAC)
Speakers 4.5 cm (1 3 / 4 q ) 6 ≠k 2
Power requirement AC 120 V, 60 Hz
Power consumption: 14 W
Memory back-up 9 V (One 6F22/6LR61, 006P bat-
tery)
Dimensions (W k H k D) 232 k 107 k 215 mm
(9 1 /
8 qk 4 3 /
16 qk 8 7 /
16 q )
Mass 1.55 k g (3 lb 6.7 oz) without bat-
tery
Note:
Specifications are subject to change without notice.
Mass and dimensions are approximate.
Specifications
Power consumption in standby mode: 1.6 W
CAUTION:
This device complies with Part 15 of the FCC Rules. Operation is
subject to the conditions that this device does not cause harmful in-
terference.
Any unauthorized changes or modifications to this equipment would
void the user’s authority to operate this device.
Open the lid and clean the lens.
Use a cotton swab to gently wipe off any finger-prints.
Recommended product:
Lens cleaner kit (SZZP1038C)
CD CLOCK RADIO
DOZE
lens
Maintaining the Lens
Inside of product
ONLY FOR CANADA