Pioneer VSX-D509S - Manual (Page 26)

26
Learning mode: Programming signals from other remote controls
(VSX-D509S only)
If preset codes are not available for your component(s), or the available preset codes do not operate correctly,
you can use this function to program in signals from the remote control(s) of your other component(s). This
operation can also be used after recalling a preset code to program additional operations not covered in the
preset codes.
1 Press SETUP and hold for 3 seconds.
The visible LED will blink twice.
2 Press the MULTI CONTROL button for the
component you want to control and then
press 9, 7, then 5 to select the LEARNING
setup mode. The remote is ready to learn new
commands from other remote controls.
The LED flashes rapidly.
To cancel LEARNING setup mode
Press SETUP button.
After ten seconds if no commands are entered the remote will
revert to its previous mode.
3 Press the button to be programmed (for
example the
3 [play] button).
4 Point the remote controls at each other, about
1-2 inches apart, and press the button on the
other remote control for the operation you
want to program .
1 Point the remote controls toward each other.
2 Press the button on the other remote control corresponding to the
operation you wish to program. The LED on this receiver’s remote
will go out and then blink twice when the operation is learned.
Press the teaching key repeatedly, varying the distances between
the remotes, until you see this receiver’s remote blink twice,
indicating the operation has been learned.
To program additional operations for the current component
Repeat steps 3 and 4.
To program operations for another component
Repeat steps 2 through 4.
5 Press SETUP to exit the LEARNING setup
mode
After ten seconds of inactivity the remote control will automatically
leave the LEARNING mode and revert to its previous mode.
Some commands from other remote controls cannot be learned,
but in most cases the remotes just need to be moved closer
together a farther apant.
1 - 2 inches
Î
SOURCE
ENTER
MIDNIGHT SIGNAL SELECT
TV CONTROL
TV VOL
TVFUNC TV MENU ENTER
D.ACCESS
BAND
CLASS
CH SELECT
CH LEVEL
AV PRE-PROGRAMMED AND LEARNING
REMOTE CONTROL UNIT DSP
TEST TONE
FL DIMMER
LOUDNESS
FUNCTION
SETUP
MUTING
MPX
DTV ON / OFF
DTV MENU
FQ FQ
ST
ST
CHANNEL
EFFECT MASTER VOLUME
DISC
+10
5.1CH
MALTI CONTROL
ATT
DVD
TV
VCR
CD-R
RCV
CD
TNU
TVC
RECEIVER
12
3
45
6
78
9
7
4
¢
3
1
¡
0
8 2
О
О
SOURCE
ENTER
TV CONTROL
TV VOL TVFUNC
TV
MENU
ENTER
D.ACCESS BAND CLASS
CH SELECT CH LEVEL
AV PRE-PROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
DSP TEST TONE
FL DIMMER
LOUDNESS FUNCTION SETUP MUTING
MPX DTV ON / OFF DTV MENU
FQ
FQ
ST ST
CHANNEL
MASTER VOLUME
DISC
MULTI CONTROL
DVD TV VCR CD-R
RCV CD TUN TVC
RECEIVER
7 4 ¢
3 1 ¡
8
2
MIDNIGHT
SIGNAL SELECT EFFECT
+10
5.1CH ATT
1 2 3
4 5 6
7 8 9
0
2 2
1,5
2
2
Preparations
LED
( )
memo
Î
SOURCE
ENTER
TV CONTROL
TV VOL TVFUNC
TV
MENU
ENTER
D.ACCESS BAND CLASS
CH SELECT CH LEVEL
AV PRE-PROGRAMMED AND LEARNING REMOTE CONTROL UNIT
DSP TEST TONE
FL DIMMER
LOUDNESS FUNCTION SETUP MUTING
MPX DTV ON / OFF DTV MENU
FQ
FQ
ST ST
CHANNEL
MASTER VOLUME
DISC
MULTI CONTROL
DVD TV VCR CD-R
RCV CD TUN TVC
RECEIVER
7 4 ¢
3 1 ¡
8
2
MIDNIGHT
SIGNAL SELECT EFFECT
+10
5.1CH ATT
1 2 3
4 5 6
7 8 9
0
The highlighted keys can
learn new functions. memo