Pioneer BDP-LX52 - Manual (Page 35)

35
En
05
• Prog.Motion is disabled when Pure Cinema is set to
On.
• Black Setup has the effect only for pictures output
f
rom the VIDEO output terminals, and for NTSC
signals out put.
• YNR, CNR, BNR and MNR have no effect on 1080/24p
video signals out
put from the HDMI OUT terminal.
 Closing the Video Adjust screen
P ress HOME MENU.
 About Pure Cinema
The re are two types of video signals:
• Video material – Video signals recorded at 25 or 30
f
rames/second
• Film material – Video signals recorded at 24 frames/
second
“Pu re Cinema” uses signal processing suited for “film
mate rial” when converting 576i/480i or 1080i interlaced
video signals into progressive video signals, resulting in
clea r picture reproduction without losing the quality of
the mate rial.
is dis played on the disc information screen when
playing the “film material” pictures of BD-ROM, BD-R/-RE
and DVD-Video discs (
page 26).
Adjusting the audio
Adjusting the Audio DRC
Audio DRC (Dynamic Range Cont rol) has the effect of
playing loud sounds softly and soft sounds loudly. Adjust
the setting fo
r example when viewing movies late at night
and the dialogs a re difficult to hear.
1 During playback, display the TOOLS menu.
P ress TOOLS.
2 Select and set Audio Adjust.
Use / to select, then press ENTER.
3 Select and set Audio DRC.
Use / to select, then press ENTER.
4 Adjust the setting.
Use
/ to switch between Off, Low, Medium, High
and Auto.
 Closing the Audio DRC screen
P ress ENTER or HOME MENU.
Note
• This only affects the Dolby T rueHD, Dolby Digital Plus
and Dolby Digital audio signals of BDs, DVDs and
video files.
• When Auto is selected, the setting has the same
effect as High or Off for Dolby TrueHD signals,
de pending on the content. For Dolby Digital Plus and
Dolby Digital, the setting has the same effect as Off.
• Audio DRC affects the audio signals out put from the
following audio out put terminals:
– Analog audio signals out put from the AUDIO OUT
te rminals.
– Linea r PCM audio signals output from the DIGITAL
OUT terminal or HDMI OUT terminal.
• The effect may be weak fo r some discs.
Adjusting the audio delay
(Lip Sync)
Adjust the audio delay fo r the selected video output
te rminal if the video and audio are not synchronized.
1 During playback, display the TOOLS menu.
P ress TOOLS.
2 Select and set Audio Adjust.
Use
/ to select, then press ENTER.
3 Select and set Lip Sync.
Use / to select, then press ENTER.
4 Select Auto or Manual.
Use
/ to select.
• Auto – The player automatically adjusts the timing of
the video and audio when connected to a device
equi
pped with the HDMI Auto Lipsync Correction
featu re using an HDMI cable.
• Manual – Adjust manually while viewing the video.
If you have selected Manual, proceed to step 5.
5 Adjusting the amount of audio delay.
P ress , then use / to adjust.
The audio delay can be adjusted f rom 0 to 250 ms in steps
of 5 ms.
Note
• The Lip Sync adjustment is only applicable to the
out put terminal set at Output Terminal (page 43).
• The sound may be inte rrupted while setting the delay.
 Closing the Lip Sync screen
P ress ENTER or HOME MENU.
TOP MENU TOOLS
HOME
MENU RETURN
ENTER
Lip Sync
Manual
100 ms
0 50 150 100 200 250
LX52_VXJ5_IBD_EN.book 35 ページ ２００９年３月３日 火曜日 午後７時２９分