Philips MDR515H / F7 - Manual (Page 57)

57 EN EN
Recording
Basic Setup
Connections
Playback
Editing
Introduction
Function Setup
Others
Español
DUBBING
Guide to DV and On-Screen Display
This function helps you to easily dub the contents of the DVC (digital video camcorder) to HDD or DVD.
You can control basic operations of the DVC from the remote control of this unit such as playback, fast forward or
reverse and stop all operations if the DVC is in video mode. Use the DV cable that has 4-pin input jack and is
compliance with the IEEE1394 standards. When you connect to DV-IN jack on the front of this unit, select “L3(DV-IN)”
position by using [SOURCE] or [CHANNEL
/ ] on the remote control and press [DISPLAY] to show the DV dubbing
information for the operation of your DVC.
1. DV icon
2. Indicator of active device
• When “Control” is highlighted,
press [OK] to display the item
selection. Use [
K /L] to select the
device you wish to operate, then
press [OK] to activate.
• Select “HDD” / “DVD” to control
this unit.
• Select “DV Input” to control your
DVC.
3. Recording audio mode
• With DVC in stop mode while
other sources are available, then
“DV Audio” can be selected. Press
[OK] to display the item selection
and then use [
K / L] to select the
audio you wish to output. Press
[OK] again to activate.
• Select “Stereo1” to dub the stereo
sound.
• Select “Stereo2” to dub the sound
with after recording sound.
• Select “Mix” to dub the stereo1
and stereo2.
4. Indicator of dubbing function
• When the unit is ready for
dubbing, “Start Rec” will appear.
• When the unit is dubbing, “Pause
Rec” will appear.
5. Channel position
•
When you select “L3(DV-IN)” by
using [SOURCE] or
[CHANNEL
/ ], “L3(DV-IN)”
will appear.
L3 (DV-IN)
AB-1234
0:12:34
1/ 1 1/ 1
+RW
Control DVD
DV Audio
Stereo1
Start Rec
L3 (DV-IN)
AB-1234
0:12:34
1/ 1 1/ 1
+RW
DVD SP(2Hr) 1h00m DVD SP(2Hr) 1h00m
2
3
1
4
5
6 7
what mode of DVC.
Switch the mode on the DVC to
playback mode for the dubbing
information.
When the DVC is
in video mode...
When the DVC is not
in camera mode...
6. Product name of your DVC
•
If the unit cannot recognize the
input signal from the DVC or the
unknown product, “No Device” or
“****” will appear instead.
7. Status of the current operation
and the time counter
The following instructions are described with the operations using the remote control of this unit.
Information on DV Dubbing
DVC is in stop mode.
DVC is in playback mode.
DVC is in pause mode.
DVC is fast forwarding.
(standard speed)
DVC is fast forwarding.
(faster than above)
DVC is fast forwarding.
(faster than above)
DVC is slow forwarding.
(standard speed)
DVC is slow forwarding.
(faster than above)
DVC is slow forwarding.
(faster than above)
DVC is fast forwarding.
(in stop mode)
DVC is fast reversing.
(in stop mode)
DVC is fast reversing.
(standard speed)
DVC is fast reversing.
(faster than above)
DVC is fast reversing.
(faster than above)
DVC is in slow reverse
playback.
DVC is recording.
DVC is in recording pause
mode.
Each icon means (Available icons may vary depending on the DVC):