Installation and maintenance, Hints on installation, Troubleshooting – Pioneer RCS-LX60D User Manual

Page 37: General, Additional information 10

Advertising
background image

Additional information

10

37

En

Installation and maintenance

Hints on installation

We want you to enjoy using this system for years to come,
so please bear in mind the following points when
choosing a location:

Do...

Use in a well-ventilated room.

Place on a solid, flat, level surface, such as a table, shelf or

stereo rack

.

Don’t...

Use in a place exposed to high temperatures or humidity,
including near radiators and other heat-generating
appliances.

Place on a window sill or other place where the system will
be exposed to direct sunlight.

Use in an excessively dusty or damp environment.

Place directly on top of an amplifier, or other component in
your stereo system that becomes hot in use.

Use near a television or monitor as you may experience
interference — especially if the television uses an indoor
antenna.

Use in a kitchen or other room where the system may be
exposed to smoke or steam.

Use on a thick rug or carpet, or cover with cloth — this may
prevent proper cooling of the system unit.

Place on an unstable surface, or one that is not large enough
to support all four of the system unit’s feet.

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with
this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other
components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks
listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.

• If the system does not operate normally due to external effects such as static electricity disconnect the plug from

the outlet and insert again to return to normal operating conditions.

• If there is no sound or no multichannel sound from the DVR-LX60D HDD/DVD recorder, try setting the recorder’s

audio-related settings back to their defaults — see

The Initial Setup menu

on page 137.

General

Problem

Remedy

The power does not turn on, or
switches off suddenly (an error
message may be displayed at
startup).

• Leave the unit plugged in, wait for one minute, then switch back on.
• Make sure there are no loose strands of wire touching the unit. This could cause the
system to shut off automatically.
• Check that the speakers are connected correctly.
• Make sure there is enough space for ventilation around the receiver subwoofer.
• Make sure the voltage of the mains power source is correct for the model.
• Try reducing the volume level.
• If the problem persists, take it to your nearest Pioneer authorized service center or your
dealer for servicing.

No sound is output when an
input function is selected.

• If you’re playing from the HDD/DVD recorder, make sure that the digital coaxial cable is
connected properly. Also make sure that the HDD/DVD recorder’s Digital Out and DTS Out
settings are set to

On

, and that the MPEG Out setting is set to

MPEG

PCM

.

• If you’re using the line input, make sure the component is connected correctly (see

Connecting auxiliary components

on page 33).

• Turn up the volume.

No sound from surround or
center speakers.

• Refer to

Channel level setting

on page 31 to check the speaker levels.

• Check that you haven’t selected the

AUTO

,

STEREO

, or

VIRTUAL

mode (see

Listening in

surround sound

on page 26).

• Connect the speakers properly (refer to

Connecting up

on page 10).

• If you’re playing from the HDD/DVD recorder, check that the Dolby Digital Out setting is
set to

Dolby Digital

.

• If the source is 96 kHz, this will be played in stereo. If you want to play it in surround
sound, set the HDD/DVD recorder’s 96 kHz PCM Out setting to

96 kHz

48 kHz

.

RCS-LX60D_WV.book 37 ページ 2007年4月24日 火曜日 午後7時57分

Advertising
This manual is related to the following products: