Nikon DSR-1500AP User Manual

Page 64

Advertising
background image

64

Menu Contents

C

h

ap
te

r 4

M
e

nu
S
e

tti

n

gs

VITC POS SEL-1 [> VITC pos-1]: Select a line to insert the

VITC in.

Note

You can insert the VITC signal in two places. To insert it in two
places, set both this item and also VITC POS SEL-2.

(For DSR-1500A)
20 LINE [>> 20 line] to 12 LINE [>> 12 line]: Select any line

from 12 to 20.

Factory default setting: 16 LINE [>> 16 line]

(For DSR-1500AP)
22 LINE [>> 22 line] to 9 LINE [>> 9 line]: Select any line

from 9 to 22.

Factory default setting: 19 LINE [>> 19 line]

VITC POS SEL-2 [> VITC pos-2]: Select a line to insert the

VITC in.

Note

You can insert the VITC signal in two places. To insert it in two
places, set both this item and also VITC POS SEL-1.

(For DSR-1500A)
20 LINE [>> 20 line] to 12 LINE [>> 12 line]: Select any line

from 12 to 20.

Factory default setting: 18 LINE [>> 18 line]

(For DSR-1500AP)
22 LINE [>> 22 line] to 9 LINE [>> 9 line]: Select any line

from 9 to 22.

Factory default setting: 21 LINE [>> 21 line]

VITC OUTPUT [> VITC out]: Select the time code to be output

as VITC.

OFF [>> OFF]: Do not output VITC.
TC [>> TC]: Output TC after converting it into VITC.
*

VITC [>> VITC]: Output VITC.

EE OUT PHASE [> EE out]: Determine the output phase for

the LTC signal output from the TC OUT connector when
recording time code and in STOP REC mode (forced EE
mode).

*

MUTE [>> mute]: Mute the output.

THROUGH [>> through]: Output the time code input to the

TC IN connector as it is. (

See example configuration on

page 70.)

VIDEO INPUT PHASE [>> V input]: Output the time code

with the same phase as the input video signal phase.
(See example configuration on page 70.)

VIDEO OUTPUT PHASE [>> V output]: Output the time code

with the same phase as the output video signal phase.
(See example configuration on page 71.)

MUTE IN SRCH [> Mute in SR]: Select whether to mute the

output from the TC OUT connector in search (jog/shuttle)
mode.

OFF [>> OFF]: Do not mute.
*

ON [>> ON]: Mute.

TAPE PROTECTION [Tape protct]: Settings related to tape
and video head protection

Description of settings

FROM STOP [> From STOP]:

Set the time to switch from
stop mode to tape protection
mode.

STOP TIMER [>> STP

timer]: Set the time to
switch from stop mode
to tape protection
mode.

0.5 SEC [>>> 0.5 sec] to 5 MIN [>>> 5 min]: Select time from

12 settings ranging from 0.5 second to 5 minutes in steps
of 0.1 second.

Factory default setting: 1 MIN [>>> 1 min]

Note

If the value is set to 1 minute or more, the unit enters internal
protection mode in 1 minute, which makes start up slower.

FROM STILL [> From STILL]:

Set the time to switch from
still search mode to tape
protection mode. Also select
the type of tape protection
mode.

STILL TIMER [>> STL

timer]: Set the time to
switch from still search
mode to tape
protection mode.

0.5 SEC [>>> 0.5 sec] to 5 MIN [>>> 5 min]: Select time from

12 settings ranging from 0.5 second to 5 minutes in steps
of 0.1 second.

Factory default setting: 1 MIN [>>> 1 min]

Note

If the value is set to 1 minute or more, the unit enters internal
protection mode in 1 minute, which makes start up slower.

NEXT MODE [>> Next

mode]: Select the type
of tape protection
mode to follow still
search mode when the
time set with the STILL
TIMER menu item
elapses.

*

STEP FWD [>>> Step]: The tape is advanced at

1

/

30

times

normal speed for about 2 seconds.

STANDBY OFF [>>> STANDBY]: Standby off mode

Note

The Step setting is enabled only when “STILL TIMER” is set to
less than 1 minute.

TIME CODE [Time code]: Settings related to the time code
generator

Description of settings

Advertising
This manual is related to the following products: