RocketFish RF-TVMFM01 User Manual

Quick setup guide

Advertising
background image

1 Install the arm assembly

Option 1: Installing to a wood stud wall

Note: Any material covering the wall must not exceed

16 mm (5/8 in.).

1 Locate the stud. Verify the center of the stud with an awl or

thin nail or use an edge-to-edge stud finder.

2 Level the arm assembly (A) and mark the hole locations.

3 Drill pilot hole to a depth of

75 mm (3 in.) using a

5.5 mm (7/32 in.) diameter drill bit.

4 Align the arm assembly (A) with the

pilot holes, insert the coach screws (G)

through the holes in the arm

assembly, then tighten

the coach screws only until

they are pulled firmly

against the arm assembly.

CAUTION: Avoid potential

injuries or property damage!

DO NOT over-tighten the

coach screws (G).

2 Attach the mounting hardware

Option 1: For TVs with inset mounting or that require extra space for wires

Install spacers (E), washers (D), and screws (C) into the top two holes in the back of the TV.

Leave a gap between the spacer and the washer and screw.

Note: Only install the hardware in the top two screw holes at this time. The remaining hardware

will be installed in Step 3.

Option 2: Installing to a solid concrete or concrete block wall

1 Level the arm assembly (A) and mark the hole locations.

2 Drill pilot hole to a depth of

75 mm (3 in.)

using a

9.5 mm (

3/8 in.) diameter drill bit.

3 Insert the concrete wall anchors (H) into the pilot holes

and make sure that the anchors are seated flush with

the concrete surface.

4 Align the arm assembly (A) with the anchors, insert

the

coach screws (G) through the holes in the arm assembly,

then tighten the coach screws only until they are pulled

firmly against the arm assembly.

CAUTION: Avoid potential injuries or property damage!

DO NOT over-tighten the coach screws

(G).

Option 2: For flat backed TVs

Install washers (D), and screws (B) into the top two holes in the back of the TV.

Leave a gap between the back of the TV and the washer and screw.

Note: Only install the hardware in the top two screw holes at this time. The remaining hardware

will be installed in Step 3.

8 in.

139.7 mm

(5-1/2 in.)

203.2 mm

(8 in.)

TV shifts

139.7 mm (5-1/2 in.)

in. from the

home position to full extension.

CAUTION: To prevent property

damage or personal injury, never

drill into mortar between blocks.

Mount wall plate directly onto the

concrete surface.

Gap

Gap

<16 mm

(5/8 in.)

QUICK SETUP GUIDE

RF-TVMFM01

Tools you will need:

• Stud finder

• Awl

• Pencil

• Level

• Tape measure

• Phillips screwdriver

• Hammer (concrete only)

• Socket wrench with

12.7 mm (1/2 in.) socket

or adjustable wrench

• 5.5 mm (7/32 in.) wood drill bit

• 9.5 mm (3/8in.) masonry drill bit

(concrete only)

• Power drill

Package contents

A Arm assembly (1)

M4 bag

B M4 × 12 mm screws (4)

C M4 × 30 mm screws (4)

D M4 washers (4)

E M4 spacers (4)

Hex key bag

F 4 mm (5/32 in.) hex key (1)

Coach Screw bag

G 8 mm (5/16 in.)× 70 mm

(2 3/4 in.) coach screw (2)

H Concrete anchor (2)

Cable ties

Thank you for choosing the Rocketfish RF-TVMFM01.

The RF-TVMFM01 TV mount is designed to support a

flat-panel TV weighing up to

15.8 kg (35 lbs.).

Lag Bolt Bag

M4

M4 × 12 mm

M4 bag

M4 × 30 mm

M4

Hex key bag

Cable ties

75 mm

(3 in.)

75 mm

(3 in.)

TV

Wall

NOTE: If the hole pattern on

your TV is 75 mm x 75 mm the

washers (D) will not be used.

NOTE: If the hole pattern on

your TV is 75 mm x 75 mm the

washers (D) will not be used.

4 mm

(5/32 in.)

8mm (5/16 in.)× 70 mm (2 3/4 in.)

RF-TVMFM01_10-0451_QSG_V2_EN_finalLR.pdf 1 8/23/2011 11:56:36 AM

Advertising
This manual is related to the following products: