Roland SP-555 - Manual (Page 60)

60
Appendix
Specify effect send for USB [EFFECT ASSIGN] + [CANCEL] + [MIC]/[LINE IN]
Specify effect send for D Beam Synth [EFFECT ASSIGN] + [SYNTH]
Effect send for current bank [EFFECT ASSIGN] + Pad [1] + [16]/ Pad [4] + [13]
Effect send for all samples [EFFECT ASSIGN] + [SUB PAD]
Effect assign mode [EFFECT ASSIGN] + [REMAIN]
Check the previous effect [EFFECT ASSIGN]
Set the parameters of the effect to use next [REMAIN] + CTRL1 knob / CTRL2 knob / CTRL3 knob
Effect limit mode [CANCEL] + [MFX]
Effect knob control [CANCEL] + [SUPER FILTER]
Reset an effect’s tempo synchronization to the tempo of
the synthesizer [EFFECT ASSIGN] + [TAP TEMPO]
Effect tempo mode [EFFECT ASSIGN] + [PATTERN SELECT]
Call up an Effect Memory [EFFECT MEMORY] ➜ Pad [1]–[16]
Store an Effect Memory [EFFECT MEMORY] ➜ [SAMPLING] ➜ Pad [1]–[16] ➜ [SAMPLING]
Check the content of an Effect Memory [EFFECT MEMORY] ➜ [REMAIN] + Pad [1]–[16]
Loop Capture operations
To accomplish this Do this
Record Loop Capture [REC] ( [REC] to stop recording, and [PLAY] to move to playback)
Play back Loop Capture (with a loop recorded) [PLAY] ( [PLAY] to stop)
Overdub Loop Capture (with a loop recorded) [REC] ( [REC] to play back, [PLAY] to stop)
Specify the Loop Capture volume [PLAY] ➜ [START/END/LEVEL] ➜ CTRL3 knob ( [START/END/LEVEL] to end settings)
Delete a Loop Capture recording (1) [DEL] ➜ [PLAY] ➜ [DEL]
Delete a Loop Capture recording (2) [EFFECT ASSIGN] + [REC]
Sample a Loop Capture to a pad [SAVE TO PAD] ➜ Pad [1]–[16] ➜ [SAVE TO PAD]
Pattern operations
To accomplish this Do this
Play a pattern [PATTERN SELECT] ➜ Pad [1]–[16]
During playback, select the pattern to play next During pattern playback Pad [1]–[16]
During playback, switch the pattern immediately During pattern playback [SUB PAD] + Pad [1]–[16]
Stop the pattern (1) [CANCEL]
Stop the pattern (2) [PATTERN SELECT] ➜ Pad [1]–[16] (the pad of the currently playing pattern)
Sequencer tempo setting (1) [PATTERN SELECT] ➜ [TIME/BPM] ➜ CTRL2 knob ( [TIME/BPM] ends the setting)
Sequencer tempo setting (2) [TAP TEMPO] + CTRL2 knob
Sequencer tempo setting (tap tempo) Press [TAP TEMPO] four or more times (display will temporarily show the pattern tempo)
Sequencer tempo setting (copy tempo from pad) [TAP TEMPO] + Pad [1]–[16] (BPM of that pad’s sample is assigned)
Record a pattern [PATTERN SELECT] ➜ [SAMPLING] ➜ Pad [1]–[16] ➜ [SAMPLING]
( [CANCEL] to stop recording)
Quantize setting During pattern recording standby / during recording [QUANTIZE] ➜ CTRL3 knob
( [QUANTIZE] ends the setting)
Specify the length of the pattern During pattern recording standby [LENGTH] ➜ CTRL3 knob ( [LENGTH] ends the setting)
Metronome on/off [METRONOME]
Specify metronome volume [METRONOME] + CTRL3 knob
To accomplish this Do this
SP-555_e.book 60 ページ ２００７年６月２５日 月曜日 午前９時９分