RCA RT2870R User Manual

Game, Bd tv vcr dvd sat/cab am/fm game/line-in source, Important safety instructions

Advertising
background image

It's important to read this instruction prior to using your new product for the fi rst time.

811-AV6291W073

RT2870R

EXPORTER

AVC Multimedia
www.RCAav.com

Printed in China

FCC INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.
Consult the dealer or an experienced radio / TV technician for help.

WARNING: Changes or modifi cations to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

This class B digital apparatus meets all requirements of the Canadian Interference - Causing Equipment
Regulations.

The Shock Hazard Marking and Associated Graphical Symbol is provided on the bottom panel of unit.

Refer to the identification / rating label located on the back panel of your product for its proper
operating voltage.

IMPORTANT: The power cord can be unplugged to turn off the main power to the unit. It should also be
easily accessible in an emergency.

Leave suffi

cient space around the appliance to allow adequate ventilation: 10cm on either side and

at the back, as well as 7cm above it are ideal.

WARNING: To reduce the risk of fi re or electric shock, do not expose this apparatus to rain or moisture.

Connections and Setup

Connections and Setup

Connections and Setup

Connections and Setup

Connections and Setup

Connections and Setup

Connections and Setup

FCC Information

FCC Information

Important Safety Instructions

Digital Input
Connect components, such as DVD players, Satellite receiver/
Cable boxes, BD (Blu-ray Disc

TM

) Players or TV’s, capable of

outputting Dolby Digital (Surround Sound) or standard PCM
(Stereo) format digital signals.
Note: “Blu-ray Disc” is a trademark of Blu-ray Disc Association.

Digital Connection
• This unit provides two optical and one coaxial digital input jacks for the connection of your

components that have digital audio outputs.

• To connect DVD player, Satellite receiver, Cable box, Blu-ray Player, or TV that has a digital audio

output, use a coaxial digital (included) or an optical digital cable (not included) to carry the audio
signal and enjoy Dolby Digital sound quality.

• A separate optical or coaxial cable is needed for each digital connection.

Connecting the speakers

Speaker wires are color-coded to match the terminals. Connect the speaker wire from the back of each
speaker to the corresponding color terminal at the back of the unit. Press down the tab to open the
terminal and insert the wire. Release the tab to lock wire in the terminal.

When connecting the speakers, make sure the polarities (“+“ speaker wire to “+“ on the unit. For example, red
wire to red terminal on the unit) of speaker wires and terminals match.

If the cords are reversed, the sound will be distorted. Do not let the speaker wires touch each other, it will
damage the Home Theater’s amplifi er.

Note:

Place the rear speakers and subwoofer a
foot or more away from TV when using
the Front Surround sound Eff ect (FSsE).

Adjust the Angle of the Speakers
To achieve the best Front Surround sound Eff ect
(FSsE), adjust the mounted front left and the rear
left speakers to the left for an angle of 25

o

- 45

o

from the center.

Adjust the mounted front right and rear right
speakers to the right in the same way.

Disconnecting the Speakers
1. To unlock the speakers, press and hold the

hinge spring as illustrated below.

2. Slide out the rear speaker from the hinge.
3. Press and hold the two hinge springs.
4. Slide out the hinge from the front speaker.

Digital Connections

The digital audio jacks can accept Dolby Digital (Surround Sound) or PCM (Stereo) signals when compatible
components are connected.

Positioning Speakers

For Your Safety

The AC power plug is polarized (one blade is
wider than the other) and only fi ts into AC power
outlets one way. If the plug won’t go into the outlet
completely, turn the plug over and try to insert it
the other way.
If it still won’t fi t, contact a qualifi ed electrician to
change the outlet, or use a diff erent one. Do not
attempt to bypass this safety feature.

CAUTION:

To prevent electric shock, match wide blade of

plug to wide slot, fully insert.
Main plug is used as disconnect device and it

should remain readily operable during intended
use. In order to disconnect the apparatus from
the mains completely, the mains plug should
be disconnected from the mains socket outlet
completely.

Service Information

This product should be serviced only by those
specially trained in appropriate servicing
techniques. For instructions on how to obtain
service, refer to the warranty included in this user
manual.

Connecting for Power

Make sure you connect all your other electronic
components and the speakers before plugging
your unit into the outlet. Plug the power cord in the
wall outlet, matching the wide blade of the plug
with the wide slot in the outlet. Be sure to insert
the plug completely.

Technical Specifi cation

Product: Audio Receiver with Dolby Digital
Brand : RCA

Electrical Consumption
Power Supply: 120V ~ 60Hz
Power Consumption: 90 Watts

This Home Theater has earned
the ENERGY STAR.

Headset Safety

Do not play your headset at a high volume.

Hearing experts warn against extended high-
volume play.
If you experience a ringing in your ears, reduce

volume or discontinu use.
You should use extreme caution or temporarily

discontinue use in potentially hazardous
situations.
Even if your headset is an open-air type

designed to let you hear outside sounds,
don't turn up the volume so high that you are
unable to hear what is around you.
Excessive sound pressure from earphones and

headphone can cause hearing loss.

THE LIGHTNING FLASH AND ARROWHEAD
WITHIN THE TRIANGLE IS A WARNING
SIGN ALERTING YOU OF “DANGEROUS
VOLTAGE” INSIDE THE PRODUCT.

THE EXCLAMATION POINT WITHIN THE
TRIANGLE IS A WARNING SIGN ALERTING
YOU OF IMPORTANT INSTRUCTIONS
ACCOMPANYING THE PRODUCT.

Please read and save for future reference.

Some of the following information may not apply
to your particular product; however, as with
any electronic product, precautions should be
observed during handling and use.

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with a dry cloth.

Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.
Do not install near any heat sources such

as radiators, heat registers, stoves, or other
apparatus (Including amplifiers) that produce
heat.
Do not defeat the safet y purpose of the

polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade or
the third prong is provided for your safety. If the
provided plug does not fi t into your wall outlet,
consult an electrician for replacement of the
obsolete outlet.
Protect the power cord from being walked on

or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
Only use attachments / accessories specifi ed by

the manufacturer.
Use only with a cart, stand, tripod, bracket, or

table specifi ed by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart / apparatus combination
to avoid injury from tip-over.

Unplug this apparatus during lightning storms

or when unused for long periods of time.
Refer all servicing to qualifi ed service personnel.

Servicing is required when the apparatus has
been damaged in any way, such as the power
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been
dropped.

Additional safety information
• Apparatus shall not be exposed to dripping or

splashing and no objects fi lled with liquids, such
as vases, shall be placed on the apparatus.

• Always leave suffi

cient space around the product

for ventilation. Do not place product in or on a bed,
rug, in a bookcase or cabinet that may prevent air
fl ow through vent openings.

• Do not place lighted candles, cigarettes, cigars,

etc. on the product.

• Connect power cord only to AC power source as

marked on the product.

• Care should be taken so that objects do not fall

into the product.

• Do not attempt to disassemble the cabinet. This

product does not contain customer serviceable
components.

If your product operates on batteries, adhere to the
following precautions:

A. Any battery may leak electrolyte if mixed with a

diff erent battery type, inserted incorrectly, or if all
batteries are not replaced at the same time.

B. Any battery may leak electrolyte or explode if

disposed of in fi re or an attempt is made to charge
a battery not intended to be recharged.

C. Discard leaky batteries immediately. Leaking

batteries can cause skin burns or other personal
injury. When discarding batteries, be sure to
dispose of them in a proper manner, according
to your state/provincial and local regulations.

D. Battery shall not be exposed to excessive heat

such as sunshine, fi re or the like.

]

Portable Cart

Warning

• One main unit
• One remote control with batteries
• One pair of front speakers, one pair of rear speakers,

one center speaker and one subwoofer

• One pair of front speaker stands (for use in Front

Surround Sound Confi guration only)

• One pig-tail antenna wire
• One AM loop antenna
• One coaxial digital cable
• One pair of audio cable for analog connections
• One English & one Spanish user manuals

Setup and Maintenance of the Unit

Provides spaces for suffi

cient ventilation as

indicated:

• Do not connect to the AC power cords until all

connections are completed.

• Do not use your set immediately after transferring

it from a cold place to a warm place: there is risk
of condensation.

• Do not expose your set to water and excessively

high temperatures.

• After having disconnected your set, clean the

case with a soft cloth, or with a slightly damp
leather chamois. Never using strong solvents.

Protec t your Components from
Overheating

• Do not block ventilation holes in any component.

Arrange the components so that air can circulate
freely.

• Do not stack components directly on top of each

other.

• Do not place the unit near other components

that generate heat such as heating vents.

• Allow adequate ventilation when placing your

components in a stand.

• Place an amplifi er near the top shelf of the stand

so heated air rising from it will not aff ect other
components. If you have a satellite receiver, you
should place it on the top shelf.

Note: Optical and coaxial cables carry only the audio portion of the signal.

Main unit

GAME

GAME

Front
speaker
stands

Left and right

front speakers

Left and right
rear speakers

Subwoofer

Center speaker

Coaxial digital

cable

Audio cable for
analog connections

Pig-tail

antenna wire

Remote

control with

batteries

BD

TV VCR DVD SAT/CAB

AM/FM GAME/LINE-IN

SOURCE

AM loop antenna

User manual

Connecting to Audio Components

DVD SAT / CAB BD

COAXIAL OPTICAL1 OPTICAL2

SAT

I I

I

I

BD

BD

DVD SAT / CAB BD

COAXIAL OPTICAL1 OPTICAL2

Optical Digital In (Audio)
Connect to optical digital output of Cable box, Satellite receiver, DVD, Blu-ray player,
TV or other compatible devices using the Optical Fiber Cable (not included).

Coaxial Digital In (Audio)
Connect to coaxial digital output of DVD, Cable box, Satellite
receiver, TV or other compatible devices using the Coaxial Digital
Cable (included).

BD/DVD/SAT/CAB/TV/GAME

BD/DVD/SAT/CAB/TV/GAME

BD/DVD/SAT/CAB/TV/GAME

Cable box

DVD player

Connecting the Antennas

Connect the AM and FM antennas to the AM and FM terminals on the system’s back panel.

They must be hooked up in order to receive clear reception. For FM reception, extend antenna to its full
length. For AM reception, rotate the antenna horizontally to get better reception.

AM Loop Antenna and FM Indoor Antenna
1. Uncoil the antenna wire and locate the base end of the AM antenna.
2. Press down on the antennas tab to open the terminal.
3. Insert the antenna wires into the terminal and release the tabs to secure the wires in place.
4. Make sure the white wire on the AM loop antenna is inserted into the AM loop terminal and the other

wire is inserted into the ground loop terminal.

3

3

1

1

2

4

Courtesy Dolby Laboratories

Note: Place the rear speakers and
subwoofer a foot or more away from

TV when using the Front Surround sound
Eff ect (FSsE).

1. Left, Right (Front Speakers)
Front speakers carry primarily music and sound
eff ects.

2. Center
In surround mode, the center speaker carries most
of the dialog as well as music and eff ects.
It should be set between the left and right
speakers.

3. Surround (Rear Speakers)
The surround speakers’ overall sound balance
should be as close as possible to the front speakers.
Proper placement is vital to establish an evenly
distributed sound fi eld.

4. Subwoofer
A subwoofer is designed to reproduce powerful
low bass eff

ects (explosions, the rumble of

spaceships, etc.).

Magnetic Shielding

Speakers placed less than two feet from the TV set
must be magnetically shielded in order to prevent
picture distortion. Center speaker provided with
this unit is magnetically shielded to protect your
TV set.

Front Speaker Placement

For best results, follow the speaker placement
below.

Alignment
Align the center speaker evenly with (A) or slightly
behind (B) (the left and right speakers), but not
ahead of them.

Angle
Place the left and right speakers to form a 45-
degree angle with your favorite viewing position
to duplicate the soundtrack mixer’s perspective.

Height
The three front speakers should be as close as
possible to the same height. This often requires
placing the center speaker directly on top (A) or
beneath (B) the TV set.

A

B

Courtesy Dolby Laboratories

Courtesy Dolby Laboratories

Courtesy Dolby Laboratories

Courtesy Dolby Laboratories

Better Surround Placement

Location
If possible, place surround speakers to either side of
the listening area, not behind it.

Height
If space permits, install surround speakers 2-3 feet
above viewers. This helps to minimize localization
eff ects.

Aiming
Aim surround speakers straight across the room,
not down at viewers, to help create a more open,
spacious surround sound fi eld.

Front Surround Mode Speaker Placement

Confi guration 1
Follow the suggestion for speaker placement in the
section before.

Alternative Surround Placement

Rear wall
If rear wall mounting is the only choice, aim the
speakers at each other (A), towards the front (B) or
towards the sidewalls (C, D).
Experiment with placement until sounds seem to
surround you, rather than come from behind you.

No adjacent walls
Surround speakers can go on stands facing each
other to approximate sidewall mounting (A), or to
the sides or rear of the viewing area, aimed upwards;
they can go right on the fl oor, or preferably, a few
feet off the fl oor such as on end tables (B).

1

1

Confi guration 2
If placing the rear speakers (surround speakers) at
the back is not a good choice for you, you can use
the Front Surround sound Eff ect (FSsE). Follow the
following instruction for setting the speakers.

Mounting the Speakers
- Place the front speaker upside down and attach

the supplied speaker stands to the top of the
front speakers.

- Slide in the hinge to the bottom of the front

speaker until the 'click' sound is heard.

- Slide in the rear speaker to the hinge until the

'click' sound is heard.

Note: Match the front left and rear left
speakers together and match the front

right and rear right speakers together.

Front

Speaker

1

2

Top

Hinge

Bottom

Speakers stand

Rear

Speaker

Front

Speaker

Rear

Speaker

Front

Speaker

Rear

Speaker

Front

Speaker

3

4

Press

and

hold

1

2

Hinge Spring

3

4

Press

and
hold

Hinge Spring

2

After adjusting the
angle, the speaker
should look like this
illustration.

User Manual

GAME

GAME

- 1 -

- 9 -

- 8 -

- 7 -

- 10 -

- 5 -

- 4 -

- 3 -

- 6 -

- 2 -

CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.

Right

Left

Rear Speakers

(Surround Sound)

Blue and Black

Grey and Black

Subwoofer

Purple and Black

White and

Black

Red and

Black

Right

Left

Front Speakers

Center Speaker

Green and Black

Use this jack on
the rear panel
to connect an
active subwoofer
other than the
one supplied.

SUBWOOFER

AUDIO OUT

Note: If your TV has digital audio output, you can connect it
to one the unit’s digital audio inputs, instead of using analog
connection.

Advertising