Tyco MX4428 User Manual
Mx4428 mxp engineering / technical manual
MX4428
MXP ENGINEERING / TECHNICAL MANUAL
MX4428 PRODUCT MANUAL
VOLUME 11
Document Number: LT0273
Issue 1.5; 24 March 2006
- APPROVALS -
AUSTRALIAN STANDARD AS4428.1
- SSL Listing Number ....................................................................................... afp1446
NEW ZEALAND STANDARD NZS4512-1997 (INCL AMDT 1 & 2)
- FPA (NZ) Listing number ................................................................................. VF/117
AS/NZS 3548 1995 CLASS A
The 4100MXP is a product of
Tyco Safety Products
211 Maces Road
Christchurch 8030
NEW ZEALAND
Phone +64-3-389 5096
Fax +64-3-389 5938
COPYRIGHT (C) 2003,2004
Information contained in this document is subject to copyright, and shall not be reproduced in any
form whatsoever, without the written consent of Tyco Services Fire & Safety.
Information contained in this document is believed to be accurate and reliable, however Tyco
Services Fire & Safety reserves the right to change the content without prior notice.
Document Outline
- Chapter 1 INTRODUCTION
- 1.1 ABOUT THIS MANUAL
- 1.2 ASSOCIATED DOCUMENTATION
- 1.3 SPECIFICATIONS
- 1.4 TERMINOLOGY
- Chapter 2 RESPONDER LOOP DESIGN CONSIDERATIONS
- Chapter 3 DEVICE INFORMATION AND PROGRAMMING
- 3.1 DEVICE TYPES
- 3.2 DEVICE HANDLING CAPABILITY
- 3.3 OUTPUT CONTROL
- 3.4 DETECTOR PARAMETER SETTINGS SUMMARY
- 3.5 DEVICE INSTALLATION
- 3.6 MX4428 PROGRAMMING
- 3.7 814H HEAT DETECTOR
- 3.8 814I IONISATION SMOKE DETECTOR
- 3.9 814PH PHOTOELECTRIC SMOKE & HEAT DETECTOR & 814P PHOTOELECTRIC SMOKE ONLY DETECTOR
- 3.10 814CH CARBON MONOXIDE + HEAT DETECTOR
- 3.11 MUB UNIVERSAL BASE
- 3.12 5BI ISOLATOR BASE
- 3.13 814RB RELAY BASE
- 3.14 814SB SOUNDER BASE
- 3.15 MKII SOUNDER BASE
- 3.16 MIM800 AND MIM801 MINI INPUT MODULES
- 3.17 CIM800 CONTACT INPUT MODULE
- 3.18 CP820 MANUAL CALL POINT
- 3.19 FP0838 / FP0839 MANUAL CALL POINTS
- 3.20 DIM800 DETECTOR INPUT MONITOR
- 3.21 RIM800 RELAY INTERFACE MODULE
- 3.22 SNM800 SOUNDER NOTIFICATION MODULE
- 3.23 LPS800 LOOP POWERED SOUNDER MODULE
- 3.24 VLC-800MX VESDA LASERCOMPACT
- 3.25 AVF / RAD / SAD / FLOWSWITCH DELAYS
- Chapter 4 ANALOGUE LOOP DESIGN CONSIDERATIONS
- Chapter 5 MXP CURRENT CONSUMPTION
- Chapter 6 EVENT LOG AND STATUS AT MX4428
- Chapter 7 MXP TECHNICAL DESCRIPTION
- Chapter 8 MXP DIAGNOSTIC TERMINAL
- 8.1 MXP DIAGNOSTIC TERMINAL OPERATION
- 8.1.1 INTRODUCTION
- 8.1.2 MENU OF COMMANDS
- 8.1.3 SELECTING POINTS FOR MONITORING
- 8.1.4 DISPLAYING DEVICE ANALOGUE VALUES - CV, TV, ETC
- 8.1.4.1 Heat Sensor of 814H, 814PH, and 814CH
- 8.1.4.2 Photo Sensor of 814PH
- 8.1.4.3 Carbon Monoxide Sensor of 814CH
- 8.1.4.4 814I Ionisation Detector
- 8.1.4.5 MIM800 Mini Input Module
- 8.1.4.6 MIM801 Mini Input Module
- 8.1.4.7 CP820 Manual Callpoint
- 8.1.4.8 CIM800 Contact Input Module
- 8.1.4.9 DIM800 Detector Input Module
- 8.1.4.10 RIM800 Relay Interface Module
- 8.1.4.11 SNM800 Sounder Notification Module
- 8.1.4.12 LPS800 Sounder Notification Module
- 8.1.4.13 VLC800 Vesda Laser Compact
- 8.1.5 ST (STATUS COMMAND)
- 8.1.6 ANALOG LOOP DIAGNOSTICS
- 8.1.7 ADVANCED COMMANDS
- 8.1.8 MX4428 DIAGNOSTICS
- 8.1.9 MXP EVENT LOG
- 8.2 FLASH PROGRAMMING
- 8.1 MXP DIAGNOSTIC TERMINAL OPERATION
- Chapter 9 DEVICE PROCESSING
- 9.1 EXPONENTIAL FILTER
- 9.2 STEP LIMITING FILTER
- 9.3 HEAT PROCESSING
- 9.4 PHOTO PROCESSING
- 9.5 CO PROCESSING
- 9.6 IONISATION PROCESSING
- 9.7 MIM800 / CIM800 / MIM801 PROCESSING
- 9.8 DIM PROCESSING
- 9.9 RIM PROCESSING
- 9.10 SNM PROCESSING
- 9.11 LPS PROCESSING
- 9.12 VLC800 PROCESSING
- 9.13 FILTER STEP LIMITS
- 9.14 ZONE ALARM TEST
- 9.15 ZONE FAULT TEST
- 9.16 AUTOTEST AND SYSTEM TEST
- 9.17 NON LATCHING TEST MODE
- 9.18 COMMISSION MODE
- 9.19 FAST POINT TEST
- 9.20 SLOW POINT TEST
- 9.21 SUMMARY OF ALL TEST MODES
- 9.22 ANCILLARY FILTERING
- 9.23 RESET
- 9.24 DEVICE INITIALISATION AND POLLING
- 9.25 SOFTWARE VERSIONS
- Chapter 10 MXP LOOP FILTER BOARD