Wayne-Dalton 900 - Manual

900 SERIES ROLLING SERVICE DOORS
1
900 SERIES
ROLLING SERVICE DOORS
GENERAL SPECIFICATIONS FOR ROLLING SERVICE DOORS Note to Specifiers: Words in parentheses indicate frequently specified and highly recommended options. PART 1 GENERAL 1.01 Work Included—The opening will be equipped with Wayne- Dalton 900 Series rolling doors, Model _____ as manufactured by Wayne-Dalton Corp. 1.02 Related Work—Opening preparation, miscellaneous or structural metal work, access panels, finish or field painting, field electrical wiring, wire, conduit, fuses, and disconnect switches are in the Scope of Work of other divisions or trades. PART 2 PRODUCT 2.01 Curtain will be composed of prime painted galvanized steel interlocking slats (A) gauge, No. (B) slats, roll-formed from (C) per ASTM standards and designed to withstand a 20 PSF windload. Ends of alternate slats will be fitted with metal endlocks/windlocks. Bottom Bar will consist of 2 equal galvanized steel (stainless steel) angles, (aluminum extrusion) minimum
1 ¼
8 "
th
ic
k,
t
o
stiffen curtain with neoprene loop astragal. When required for additional security, provide (slide bolts) (cylinder locks) on the bottom bar operable from (coil side) (opposite coil side) (both sides).
2.02 Guides will be of roll-formed galvanized steel channels and angles (three angle assembly) of steel (stainless steel) (aluminum) to form a slot of sufficient depth to retain curtains in guides to resist 20 PSF windload. Guides may be provided with integral windlock bars and removable bottom bar stops. 2.03 Brackets will be of galvanized steel plates with permanently sealed ball bearings. Designed to enclose ends of coil and provide support for counterbalance pipe at each end. 2.04 Counterbalance: Curtain to be coiled on a pipe of sufficient size to carry door load with deflection not to exceed .03 inches per foot of door span and to be evenly balanced by helical springs, oil tempered torsion type designed with a 25% safety factor. Cast iron barrel plugs will be used to anchor springs to tension shaft and pipe. 2.05 Hood will be minimum 24 gauge (prime painted galvanized) (galvanized) (slatted) steel, flanged at top for attachment to header and flanged at bottom to provide longitudinal stiffness. Hood will enclose curtain coil and counterbalance mechanism. 2.06 Finish: Shop coat of rust inhibitive primer on non-galvanized surfaces and operating mechanisms. Aluminum finish to be (mill) (204R1 clear anodized) (bronze anodized). Stainless steel finish to be (#4). Curtain will be (white) (blue) (gray) (tan) (brown).
2.07 Operation: Door will be operated by means of (manual, push-up) (chain hoist with gear drive reduction) (awning crank) (wall crank box) (motor operation). (Electrical) (Pneumatic) sensing edge to be attached to bottom bar to (stop) (stop and reverse) the door when it contacts an object during the closing cycle. 2.08 Weatherstripping: Air- Bar/Extr-Tite doors will include flat slats, bottom astragal, exterior surface guide weatherstrip, and internal hood baffle weatherstrip. 2.09 Locking: (Manual push-up doors will have interior slide-bolts suitable for padlocks by others.) (Chain-hoist door will have chain keepers suitable for padlocks by others.) (Electric-motor operation doors will lock through the operator gearing.) (Cylinder locks can be provided with the doors.) CAUTION: When specifying cylinder locks on electric-motor operated doors, electric interlocks should also be specified to prevent operation when lock bolts are engaged in the guides, thus preventing damage to the curtain and/or operator. PART 3 EXECUTION 3.01 Install the doors in accordance with Wayne-Dalton Corp. instructions and standards. Installation and maintenance will be by an authorized Wayne-Dalton representative. Because of continuing product improvements, we reserve the right to change the product specifications and designs without prior notice.
WAYNE-DALTON CORP. • ONE
DOOR
DRIVE • MT. HOPE, OH 44660 • PH. 800-764-1457 • FX. 800-336-
1422
For easier door specifications or product questions call the WayneTec Consulting Service
1
-8
0
0
-76
4
-1
4
57
.
COLORS INCLUDE: (22 and 24 gauge only) White Blue Gray Tan Brown
©2001 Wayne-Dalton Corp.
Rev. 11/01 246570