Yamaha HTR-6090 - Manual (Page 100)

96
En
CUSTOMIZING THIS UNIT (MANUAL SETUP)
Use this menu to adjust the optional system parameters.
■ Display settings
A)DISPLAY SET
Use the “V-RESET” in “ADVANCED SETUP” to set the
parameters in “DISPLAY SET” (except “DIMMER”, “SHORT
MESSAGE”, “ON SCREEN” and “FL SCROLL”) to the factory
presets (see page 119).
Dimmer DIMMER
Use this feature to adjust the brightness of the front panel
display.
Control range: –
4 to 0
Control step: 1
• Press l to make the front panel display dimmer.
• Press h to make the front panel display brighter.
OSD shift OSD SHIFT
Use this feature to adjust the vertical position of the OSD.
Control range: –5 (upward) to +5 (downward)
Control step: 1
Initial setting: 0
• Press l to raise the position of the OSD.
• Press h to lower the position of the OSD.
Gray back GRAY BACK
Use this feature to display a gray background in your
video monitor when there is no video signal being input.
Choices: AUTO, OFF
• Select “AUTO” to display a gray background in your
video monitor when there is no video signal being
input.
• Select “OFF” not to display a gray background in your
video monitor.
• Depending on the video signals being input or the system
setting of your video monitor (NTSC or PAL), the OSD may be
displayed abnormally. In such cases, set “GRAY BACK” to
“OFF”.
• Even when “GRAY BACK” is set to “OFF”, the OSD may not
be displayed correctly depending on the conditions of the
picture.
Video conversion V CONV.
Use this feature to set whether to convert the video signals
input at the VIDEO, S VIDEO and COMPONENT
VIDEO jacks.
Choices: ON, OFF
• Select “ON” to convert composite, S-video and
component video signals interchangeably and up-
convert composite and S-video and component video
signals to HDMI video signals.
• Select “OFF” not to convert any signals.
• This unit does not convert 480 line video signals and 576 line
video signals interchangeably.
• The analog component video signals with 480i (NTSC)/576i
(PAL) of resolution are converted to the s-video or composite
video signals and output at the S VIDEO MONITOR OUT and
VIDEO MONITOR OUT jacks.
• The converted video signals are only output at the MONITOR
OUT jacks. When recording a video source, you must make the
same type of video connections between each component.
• When composite video or S-video signals from a VCR are
converted to component video signals, the picture quality may
suffer depending on your VCR.
• Set “V CONV.” to “ON” to display the sound field parameter
display and short message display.
• Unconventional signals input at the composite video or S-video
jacks cannot be converted or may be output abnormally. In such
cases, set “V CONV.” to “OFF”.
• When non-standard video signals (such as video signals from a
game console) are input, this unit may not convert the signals
even if you set “V CONV.” to “ON”.
4 OPTION MENU
Note
. A)DISPLAY SET
B)MEMORY GUARD
C)AUDIO SELECT
D)DECODER MODE
4 OPTION MENU 1/2
[ ]/[ ]:Up/Down
[ENTER]:Enter
p
p
. E)PARAM. INI
F)ZONE SET
G)XM RADIO SET
H)DOCK SET
4 OPTION MENU 2/2
[ ]/[ ]:Up/Down
[ENTER]:Enter
p
p
. DIMMER;;;;;;;;;;0
OSD SHIFT ;;;;;;;0
GRAY BACK ;;;;AUTO
V CONV. ;;;;;;;;ON
[ ]/[ ]:Up/Down
[ ]/[ ]:Adjust
A)DISPLAY SET
p
p
p [
Notes
Notes
01EN_00_HTR-6090_U.book Page 96 Tuesday, June 27, 2006 6:40 PM